My CO2 visual cutting equipment uses the RDV6332M controller. While initializing the equipment, I found that the controller cannot complete the normal calibration process. Can someone help me solve th...

• CO₂ visual cutting
• RDV6332M
• control system
• RuiDa

My CO2 visual cutting encountered recognition bias issues when using the RDV6332M controller. Whenever the system performs automatic recognition, the output results always have certain errors compared...

• CO₂ visual cutting
• RDV6332M
• control system
• RuiDa

My CO2 visual cutting machine uses the RDV6332M control system. When I adjust the camera exposure and gain parameters, the operation response is significantly slow. Every time I adjust the parameters,...

• camera
• CO₂ visual cutting
• RDV6332M
• control system
• RuiDa

My device is using the RDV6332M control system, and I was about to perform visual positioning, but I found that the camera lighting was never on. Whether switching the light source switch in the softw...

• camera
• CO₂ visual cutting
• RDV6332M
• control system
• RuiDa

My CO2 visual cutting machine uses the RDC6685U-DFM control system. After processing, I found that there was a significant deviation between the finished product shape and the original design. At firs...

• CO₂ visual cutting
• RDC6685U-DFM
• control system
• RuiDa

My CO2 vision cutting equipment is paired with the RDV6445G control system. During vision positioning, I've encountered instances where mark points are either misidentified or not recognized at all. A...

• camera
• CO₂ visual cutting
• RDV6445G
• control system
• RuiDa

RDC6445GZ-DFM-RD control system, when I opened the template file, the interface did not display the corresponding graphic content, and the template list was empty. Is this due to file corruption or so...

• CO₂ visual cutting
• RDC6445GZ-DFM-RD
• control system
• RuiDa

Hello everyone! I am adjusting the CO2 visual cutting equipment, and the control system is RDV6445G. During the calibration process, the equipment cannot respond correctly to the set parameters, causi...

• CO₂ visual cutting
• RDV6445G
• control system
• RuiDa

My device is using Ruida's control system RDC6445GZ-DFM-RD, but I found that the network camera cannot display images. I connected the network camera and confirmed that all hardware connections are wo...

• camera
• CO₂ visual cutting
• RDC6445GZ-DFM-RD
• control system
• RuiDa

The control system used for my CO2 visual cutting equipment is RDC6612U-DFM. When I conducted a matching test, I found that the material could not be recognized. Is it a problem with the sensor? Or is...

• camera
• CO₂ visual cutting
• RDC6612U
• control system
• RuiDa

My CO2 vision cutting machine uses the RDV6445G controller. Today, when I was debugging, I found that the system could not recognize the device properly after connecting the camera through the USB int...

• camera
• USB
• CO₂ visual cutting
• RDV6445G
• RuiDa

When I was using the RDC6445GZ-DFM-RD controller for edge lifting operations, I found that the black edges on the top and bottom of the finished graphics were not uniform. At the initial stage of proc...

• CO₂ visual cutting
• RDC6445GZ-DFM-RD
• control system
• RuiDa

Hello everyone! My CO2 visual cutting machine uses the RDC6685U control system, and in order to achieve accurate images, I specially performed cross correction. The parameters on the screen look norma...

• camera
• CO₂ visual cutting
• RDC6685U
• control system
• RuiDa

My CO2 visual control system is RDC6612U-DFM, and I found that the equipment recognizes Mark points within the processing range but frequently prompts distance limitations. Even though the location is...

• CO₂ visual cutting
• RDC6612U
• control system
• RuiDa

I encountered a flashing issue while using the RDC6445GZ-DFM-RD control system for calibration. Whenever attempting to enter calibration mode or make parameter adjustments, the system will suddenly sh...

• CO₂ visual cutting
• RDC6445GZ-DFM-RD
• control system
• RuiDa