The control system used for my device is RDC6332NM. During device debugging, there was an abnormality in the XY axis: the zeroing action was normal, but there was no response in both axes when executi...

• coordinate axis
• RDC6332NM
• CO₂ laser
• laser cutting
• RuiDa

My device is paired with the RDC6332NM control system. Every time the system triggers an alarm, the relay should trigger the alarm light to flash, but in reality, the alarm light never lights up. Chec...

• RDC6332NM
• control system
• RuiDa

The control system used for my device is RDC6332NM. During the machining task, I tried to activate the device by calling the preset positioning point through the controller panel, but the machine neve...

• RDC6332NM
• control system
• laser cutting
• RuiDa

As soon as my RDC6332NM control system is powered on, the cutting head always moves upwards without stopping. It switches to manual mode, which can control the motor movement, and then switches to aut...

• motion system
• RDC6332NM
• control system
• RuiDa

My device is equipped with the Ruida control system RDC6332NM. After normal connection, when I press the automatic focus button, the cutting head keeps moving upwards and cannot stop. Is there a malfu...

• motion system
• RDC6332NM
• control system
• RuiDa

My CO2 laser cutting equipment is equipped with the Ruida control system, model RDC6332NM. In the spot shooting mode, when I press the start button, it cannot emit light. I checked the laser power sup...

• power supply
• RDC6332NM
• cooling system
• CO₂ laser
• RuiDa

My CO2 laser cutting equipment uses the Ruida control system, model RDC6332NM. Today, I started processing normally, but found that it cannot be reset to the origin. Can anyone help check? Thanks!

• coordinate axis
• RDC6332NM
• control system
• CO₂ laser
• RuiDa

Hello everyone! I have a question to ask for help. I have been using the RDC6332NM controller for several months now. Today, I checked the laser output status and pressed the test button "." on the pa...

• motion system
• RDC6332NM
• control system
• RuiDa

Hello everyone, I have another question regarding the RDC6332NM controller. After completing a machining operation, the equipment did not return to its preset positioning point, preventing the next ma...

• RDC6332NM
• control system
• laser cutting
• RuiDa

After I turned on the CO2 cutting machine, the RDC6332NM control system seemed to be functioning normally. However, when setting the positioning point before processing, a problem occurred. No matter ...

• RDC6332NM
• control system
• CO₂ laser
• laser cutting
• RuiDa

It's really frustrating. The controller equipped on my CO2 laser cutting machine is RDC6332NM. Everything else is fine, but after inserting a USB flash drive, it cannot be accessed. My USB flash drive...

• USB
• RDC6332NM
• control system
• CO₂ laser
• RuiDa

My equipment is equipped with an RDC6332NM controller. I am trying to connect the servo card to both the protection port and the regulator simultaneously. How can I wire it? I am worried that the wiri...

• RDC6332NM
• control system
• laser cutting
• RuiDa

My CO2 cutting machine uses the RDC6332NM controller, and when previewing the file, the HMI pops up "No Connected Device". Is there a problem with the link between the device and the controller?

• RDC6332NM
• control system
• CO₂ laser
• laser cutting
• RuiDa

My equipment uses the RDC6332NM control system, which allows for normal cutting. However, when I use the engraving function in RDWorksV8, it does not execute properly. What could be the reason for thi...

• password
• RDC6332NM
• laser engraving
• control system
• RuiDa

It's strange. Today, when I tried to operate the machine, the green power indicator light on the controller didn't light up at all. The device showed no signs of power-on startup and was in a complete...

• power supply
• RDC6332NM
• control system
• laser cutting
• RuiDa