The operating environment of laser marking machineThe laser marking machine must ensure a relatively clean surrounding environment during the production process, free from any interference from dust, grease, and chemical pollutants, which can accelerate the aging and damage of the laser marking machine.The impact of environmental dust on laser ma...

Gilbert

02-27

520

0

0

If you at the TWhat causes the arrow tips in the corners of the T all other fonts have it also except the OThis an Arial font which has been switched from a Sans Sherif font which did the same thing.From what I can see I have nothing extra switched onThe strange thing is if I increase the power the arrows go away which doesn’t work in this case. Th...

이야기 너와

02-17

510

6

1

Fault in the fiber optic section1. Fiber breakage: Fiber breakage is the most common situation in fiber laser machine failures, usually occurring in fibers that have been in use for a long time or have been excessively bent. The solution is to replace the fiber with a new one.2. Fiber optic pollution: When the surface of the fiber optic cable is co...

Smith

02-20

483

0

0

Principle of adjusting laser powerThe power of the laser marking machine directly determines the depth and speed of marking. Different materials have different requirements for laser power, and adjusting the laser power to be just right can ensure the best marking effect.Choose the appropriate power size1. Metal materials:For metal materials, hig...

Jamie

02-15

542

0

0

1. When the vertical light is incorrect, adjust the vertical light and if necessary, readjust the light path. 2. If the focal length is not adjusted properly, please refocus.3. Voltage instability, low voltage, and low laser current. You need to replace the voltage regulator with a larger one and increase the laser current output.4. If the lig...

Vasili

01-22

667

1

0

To achieve deep marking, we can adjust the parameters of the laser marking machine through the following methods:1. Adjust the focal lengthReduce the focal length to the minimum to ensure that the laser beam can be accurately focused on the surface of the material, thereby achieving the goal of deep marking.2. Adjust the laser powerLaser power i...

Liam

01-22

562

0

0

Reasons for inaccurate rotation axis1. During the use of the machine, the accuracy of the rotating shaft may decrease due to wear and tear or maintenance requirements;2. Poor manufacturing quality of the rotating shaft itself may also lead to inaccurate issues;3. During the operation of the laser engraving machine, improper control of processing sp...

Gilbert

01-21

509

0

0

In the daily operation of laser equipment, the constant emission of light is a common and difficult problem to solve. It not only affects the quality of the product, but may also increase the maintenance cost of the equipment. Faced with the problem of continuous light emission, it is urgent to quickly and accurately diagnose the location of the fa...

Abel

01-10

633

3

3

The occurrence of ghosting or blurriness during engraving operations on laser marking machines may be due to various reasons. To solve this problem, it is usually necessary to follow the following steps to check and adjust:1. Check the optical system:Confirm whether the laser and its optical components (such as lenses) are clean, as dust and stai...

Miller

2024-12-27

559

1

3

1. Fault phenomenon one: The laser marking machine does not produce laser lightThe troubleshooting steps are as follows:Power supply inspection: Firstly, it is necessary to confirm whether the power supply wiring of the laser is correct, including whether+24V and GND are reversed, and whether the ground wire is properly grounded. Test whether the...

Terrelle

01-09

584

1

2

1、 Waterway inspectionThe main reason for abnormal water flow in the laser is due to water blockage or pump failure. Therefore, we first need to check whether the water path of the laser is blocked and whether it is well connected. If there is a blockage in the waterway, it is necessary to clean or replace the local water pipe and exhaust it. If th...

Keegan

01-06

480

0

1

Hello,we are encountering an issue with our F1 Ultra in combination with Lightburn.We recently updated everything to the newest version (XCS 2.3.24 / Lightburn 1.7.04 / F1 Ultra 40.52.012.2020.01.ht5 / Plugin 1.4.22)Today, we experienced a phenomenon where the laser suddenly shifted 1 cm to the left in the middle of the engraving. It then continued...

Erdogan

2024-12-31

682

2

0

Reasons for Laser Weakening in Laser Marking MachinesThere may be various reasons for the weakening of laser marking machine, and the following are some common reasons:1. Lens damage: If the lens is scratched, overheated, or contaminated, it can cause poor reflection and weaken the laser marking machine.2. Laser tube aging: The lifespan of laser tu...

Christian

2024-12-21

521

1

0

What is the reason for the jumping of the laser marking machine?Many people encounter jumping problems when using laser marking machines, which may be caused by the following factors:1. Machine malfunction: Long term non-stop operation of the laser marking machine during use can cause the equipment to overheat, thereby affecting its working effic...

Payson

2024-12-17

544

0

1

Power failure1. Check if the power cord is securely plugged in;2. Check if the power cord is damaged;3. Check if the power supply is working properly.Laser malfunction1. Check if the laser is working properly;2. Check if the laser cable is securely plugged in;3. Check if the laser cable is damaged.Other reasons1. Check if the light tube has expi...

Clarence

2024-12-04

535

0

0