- Não resolvido
What factors cause the RDC6563FG control system's tracking alarm?
Hello! I am operating the device and the control system is RUIDA's RDC6563FG. When I was about to start processing, a warning popped up on the system interface, indicating that the status of the follo...
- RDC6563FG
- control system
- RuiDa
- 2 usuários responderam
210 - Resolvido
The RDC6563FG control system has triggered a machine protection alarm
Hello everyone! My fiber laser cutting machine uses the RDC6563FG control system. I was operating it normally when the machine protection alarm light came on the control panel, and the system stopped ...
- RDC6563FG
- fiber laser
- control system
- laser cutting
- RuiDa
- 3 usuários responderam
244 - Resolvido
Why did the RDC6563FG controller fail to read files from the USB drive?
I am using the RDC6563FG control system and have encountered a frustrating issue where the USB drive failed to read files. I plugged in the USB flash drive as usual, but there was no response on the p...
- USB
- RDC6563FG
- control system
- RuiDa
- 2 usuários responderam
235 - Resolvido
How to solve the problem of Z-axis servo alarm in RDC6563FG controller?
Hello everyone! I have a fiber laser cutting machine that is equipped with a Ruida control system, model RDC6563FG. During use, the machine suddenly triggered a Z-axis servo alarm. When an alarm occur...
- motion system
- coordinate axis
- RDC6563FG
- control system
- RuiDa
- 2 usuários responderam
216 - Não resolvido
Wie kann ich den RDC6563FG richtig einstellen?
Wie stelle ich den Controller richtig ein? die Motoren haben 3200 puls pro Umdrehung an der Y Achse sind zwei SFU1605 diese haben 5mm bei einer Umdrehung. also nach 3200 pulsen ist meine Maschine 5m...
- RDC6563FG
- 1 usuário respondeu
247 - Resolvido
Why do the wireless handheld box buttons of RDC6563FG controller malfunction?
I found a headache when using the wireless handheld box of RDC6563FG controller: the buttons occasionally malfunction. Every time the button is pressed, there is no immediate response, and sometimes t...
- RDC6563FG
- control system
- RuiDa
- 3 usuários responderam
227 - Resolvido
Could you please help with an encoder error on the RDC6563FG control system?
I have a fiber laser device that is paired with the RDC6563FG control system. As I was about to start cutting, the screen displayed a prompt saying "Encoder Error" and the machine emitted a short alar...
- motion system
- coordinate axis
- RDC6563FG
- control system
- RuiDa
- 3 usuários responderam
232 - Resolvido
What is the reason for the failure of A-axis reset of RDC6563FG controller?
Hello everyone! I am looking for help again. The A-axis reset of my RDC6563FG control system failed, and both the X and Y axes were able to move to the limit position and complete the reset normally. ...
- motion system
- coordinate axis
- RDC6563FG
- control system
- RuiDa
- 2 usuários responderam
219 - Resolvido
Why does RDC6563FG not stop touching the metal plate during capacitor calibration?
Can anyone help me? My device is paired with the RDC6563FG control system, and I am preparing to perform capacitor calibration. Following the procedure, I slowly adjusted the probe position to bring i...
- RDC6563FG
- laser head
- fiber laser
- control system
- RuiDa
- 3 usuários responderam
259 - Não resolvido
Контроллер RDC6563FG подойдет ли сервопривод к оси Z AC SERVO DRIVE TH-T3D-L15A-RABN
Контроллер RDC6563FG подойдет ли сервопривод к оси Z AC SERVO DRIVE TH-T3D-L15A-RABN
- RDC6563FG
- 1 usuário respondeu
206 - Resolvido
How to solve the air pressure alarm of RDC6563FG control system?
Hello everyone! I have a fiber laser cutting machine with a control system of RDC6563FG. During my routine inspection today, I found that there has been a continuous air pressure alarm. Where is the p...
- RDC6563FG
- fiber laser
- control system
- laser cutting
- RuiDa
- 2 usuários responderam
246 Fiber laser control system,the reason for the significant deviation between the following height and the actual height
In fiber laser control systems(RDC6563FG, RDV6563FG-NET), if there is a significant deviation between the following height and the actual height, it may be caused by the following factors: 1. Long ti...
- assist gas system
- RDV6563FG-NET
- RDC6563FG
- laser head
- RuiDa
Thomas21800The processing method for the shaking of the cutting head of the fiber laser controller at any time
During the processing of fiber laser cutting equipment(RDC6563FG, RDV6563FG-NET), if there is significant shaking of the cutting head when it follows the height, it will not only affect the cutting st...
- assist gas system
- RDV6563FG-NET
- RDC6563FG
- fiber laser
- RuiDa
Howard19800The fiber laser control system triggered the limit switch without cause
When using fiber laser equipment, if the fiber laser controller(RDC6563FG, RDV6563FG-NET) has the limit switch enable function activated, the system interface typically displays a “limit switch trigge...
- RDV6563FG-NET
- RDC6563FG
- fiber laser
- control system
- RuiDa
Adrian20700Solution to capacitance calibration failure of fiber laser cutting control system
The reason for the failure of capacitor calibration in the fiber laser cutting control system (RDC6563FG, RDV6563FG-NET) may involve multiple issues. Here are several common causes of malfunctions and...
- RDV6563FG-NET
- RDC6563FG
- laser head
- fiber laser
- RuiDa
Matthew22311
RDC6563FG
57
Tópicos8
Seguidores
Aguardando respostas
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.