chanelink logo
CHANELINK
Polski

TSMC's first European wafer fab receives € 5 billion subsidy for construction

377
2024-08-26 13:41:59
Zobacz tłumaczenie

Recently, TSMC held a groundbreaking ceremony for its first European 12 inch wafer fab. It is reported that the European Union has approved Germany to provide 5 billion euros in subsidies for the factory.

It is understood that TSMC's 12 inch wafer fab is located in Dresden, Germany and is called "European Semiconductor Manufacturing Company (ESMC)". In August 2023, TSMC announced a partnership with Bosch, Infineon, and NXP to jointly invest in the establishment of ESMC. TSMC holds a 70% stake and is responsible for operations, while Infineon, NXP, and Bosch each hold a 10% stake, with a total investment of approximately 10 billion euros.

The wafer fab is expected to introduce 28/22 nm planar complementary metal oxide semiconductor (CMOS) technology and 16/12 nm fin field-effect transistor (FinFET) processes, with an initial monthly production capacity of approximately 40000 12 inch wafers. According to the planned construction schedule, the factory will start construction in the fourth quarter of 2024, with equipment expected to enter the factory in the third quarter of 2026 and mass production starting as early as the fourth quarter of 2027.

It is worth noting that at the foundation ceremony, EU Executive Committee President von der Leyen announced that the EU has approved to provide 5 billion euros of subsidies for Dresden wafer factory.

In fact, in addition to building factories in Germany, TSMC is also investing heavily in setting up factories in the United States and Japan. However, industry insiders point out that TSMC's expansion overseas will face a series of challenges, including high operating costs, labor shortages, cultural differences, and more. For example, the German Silicon Valley Association reminds that the German labor union has a strong and tough attitude, which is one of the challenges that TSMC must overcome.

Source: Yangtze River Delta Laser Alliance

Powiązane rekomendacje

  • Which automotive parts can use laser soldering technology

    Laser soldering is widely used in the manufacturing of automotive parts. Here are some common automotive parts that can be welded using laser soldering:Automotive electronic control systemEngine Control Unit (ECU): The engine control unit is the "brain" of the car engine, which receives signals from various sensors and controls the operation of the engine based on these signals. Laser soldering ca...

    02-10
    Zobacz tłumaczenie

  • Construction of Advanced New Laser Research Centers in American Universities

    The ATLAS R&D center is expected to be completed by mid-2026!A powerful new laser research facility located on the Foothills campus of Colorado State University will begin construction this month. The facility is planned to be put into use in mid-2026 and is the result of 40 years of laser development research at Colorado State University. It is a collaboration with the Fusion Energy Science P...

    2024-10-30
    Zobacz tłumaczenie

  • Han's Laser's net profit in the third quarter decreased by 45.37% year-on-year

    Recently, Han's Laser released a third quarter report, stating that the company achieved a revenue of 3.301 billion yuan in the third quarter, a year-on-year decrease of 8.96% (after adjustment); The net profit attributable to shareholders of the listed company was 209 million yuan, a year-on-year decrease of 45.37% (after adjustment).During the reporting period, the company's operating profit, to...

    2023-10-25
    Zobacz tłumaczenie

  • Pressure sensing using dual color laser absorption spectroscopy

    The research team led by Professor Gao Xiaoming and Professor Liu Kun of the Chinese Academy of Sciences Hefei Institute of Physical Sciences recently designed a concentration independent pressure sensing technology for high-temperature combustion diagnosis. This method is based on dual color laser absorption spectroscopy.The results of this study have been published in Optics Letters.Aircraft eng...

    2024-03-09
    Zobacz tłumaczenie

  • Comparison of Blue and Infrared Wavelength in Pure Nickel Laser Deep Fusion Welding Process

    It is reported that researchers from BIAS Bremer Institution f ü r angewandte Strahltechnik GmbH in Germany have reported a comparative study of laser deep penetration welding processes for pure nickel using blue and infrared light wavelengths. The related research was published in Welding in the World under the title "Process comparison of laser deep penetration welding in pure nickel using blue ...

    2024-08-13
    Zobacz tłumaczenie