Nederlands

An efficient femtosecond pulse amplification technique for extracting the maximum stored energy in fiber laser amplifiers

972
2024-11-13 11:55:15
Bekijk vertaling

The well-known journal Optica published a paper in November 2024 titled "Near complete extraction of maximum stored energy from large core fibers using coherent pulse stacking amplification of femtosecond pulses"The authors of the paper were the University of Michigan, Lawrence Berkeley National Laboratory, Peking University, and the German Institute of Synchrotron Radiation.

The specific technique is to use a cascaded "GTI" (Gire Tounois interferometer) method to synthesize 81 amplified pulses together in the time domain. The technical difficulty that needs to be overcome is to control the phase and amplitude of each pulse to achieve coherent synthesis. The core femtosecond light source is a 1 GHz repetition rate femtosecond fiber laser, developed by Professor Zhang Zhigang's group at the School of Electronics, Peking University.

The author of the paper has demonstrated using the aforementioned techniques that, with a continuous pump of 100 W and a repetition rate of 2 kHz, nearly 10 mJ of amplified pulse energy can be extracted, far exceeding the energy output of conventional large mode area fiber amplifiers, which can reach less than 1 mJ. The extraction efficiency is close to 90%.

This efficient time-domain pulse synthesis technique can greatly improve the efficiency of pulse synthesis and reduce the number of amplifiers used for spatial synthesis.

Although the repetition rate and pulse energy obtained from this experiment are not yet high, this technology demonstrates the potential to generate femtosecond strong laser pulses with Joule level pulse energy and repetition rates above 10 kHz. It may provide a light source for studying strong field physics and particle accelerators under extreme conditions, as well as for generating secondary radiation.

Figure 1 shows the efficiency of pulse energy extraction in a fiber amplifier independent of core diameter under nonlinear confinement. Figure 1 indicates that the pulse extraction efficiency can only approach 100% of the amplifier's stored energy when the pulse is broadened to 100 ns


Figure 2 shows a schematic diagram of a composite GTI cavity, where 81 incident laser pulses are coherently superimposed in four large loop cavities to form 9 pulses; Then coherently superimpose them into one pulse in four small cavities


Figure 3: Photo of the Composite GTI Chamber Experimental Device


Figure 4 shows the pulse waveform and spectrum of the coherent synthesized pulse with an energy of 3 mJ and a width of 313 fs

Source: Yangtze River Delta Laser Alliance

Gerelateerde aanbevelingen
  • Breakthrough! Extending the lifespan of solar panels to 50 years using lasers

    Recently, the National Renewable Energy Laboratory (NREL) under the US Department of Energy has made a revolutionary breakthrough by developing a concept validation method aimed at completely removing polymers from solar panel manufacturing, thereby achieving more efficient and environmentally friendly recycling.Solar panels have always been praised for their recyclability. However, the thin plast...

    2024-04-30
    Bekijk vertaling
  • China University of Science and Technology has made progress in the study of the regulatory mechanism of thermally induced delayed fluorescence

    Recently, Professor Zhou Meng's research group at the University of Science and Technology of China collaborated with Professor Fu Hongbing's team at the Capital Normal University to reveal the mechanism by which aggregation effects regulate the luminescent properties of thermally delayed fluorescent materials. The research findings, titled "Aggregation Enhanced Thermally Activated Delayed Fluoros...

    2024-06-28
    Bekijk vertaling
  • Additive Manufacturing Software Market 2025: Analysis, Data, and Forecasting

    In March 2025, Additive Manufacturing Research (AMR) released its latest 3D printing market research report, "AM Software Markets 2025: Analysis, Data, and Forecast," which provides a comprehensive and in-depth analysis of the 3D printing software industry. The latest research findings indicate that global revenue from additive manufacturing (AM) software is expected to grow from $2.44 billion in ...

    03-17
    Bekijk vertaling
  • Filatek: Leading the Development of Laser, Shining "Additive Prince"

    In recent years, the field of laser technology has received widespread attention from the outside world. At that time, the Munich Shanghai Electronic Production Equipment Exhibition was successfully held in Shanghai, and Suzhou Feilaitek Laser Technology Co., Ltd. (hereinafter referred to as "Feilaitek"), a leading enterprise in the field of industrial laser 3D dynamic focusing systems, appeared a...

    2024-04-12
    Bekijk vertaling
  • Stable lasers developed with mixed materials focus on autonomous vehicle, etc

    Researchers printed microscale lenses directly onto optical fibers, allowing them to tightly combine the fibers and laser crystals into a single laser oscillator.Scientists have used 3D printing polymers in new micro optical technology, which can reduce the size of lasers and be used in various new applications, including the laser radar system for autonomous vehicle technology and cancer treatmen...

    2024-01-22
    Bekijk vertaling