The difference between single-mode laser and multi-mode laser
In the vast expanse of laser technology, single-mode lasers and multi-mode lasers are like two brilliant stars, each shining with its own unique radiance. As a manufacturer deeply involved in the fiel...
- laser source
- diode laser
- fiber laser
Christian1.5K00Analysis of Fault Causes in Fiber Laser Machine System
Fault in the fiber optic section 1. Fiber breakage: Fiber breakage is the most common situation in fiber laser machine failures, usually occurring in fibers that have been in use for a long time or ha...
- power supply
- fiber laser
Smith1.4K00How to use the fiber optic cutting control card
The fiber cutting control card is the control core of the fiber laser cutting machine. It is a motion control card that, by connecting to a PC and leveraging the powerful computing power of the PC, ca...
- fiber laser
- control system
- laser cutting
Payson1.4K00What are the types of fiber optic vision cutting control systems
The fiber cutting control system is the control core of the fiber laser cutting machine. The operator transfers files to the fiber cutting control system and sets the corresponding parameters before s...
- fiber laser
- control system
- laser cutting
Marshall1.3K01Unable to input commands in the console
I’m trying to see my GRBL settings, but I can’t type anything into the command window. Side note: I’m new to this, and I’m only trying to see these settings to address a different issue. I have a Monp...
- LaserGRBL
- fiber laser
Tim Johnson1.4K20Settings cannot be saved across machines
I am using a co2 omtech laser with my fiber laser. When I switch between the 2 machines the orientation of my project has to be adjusted in machine settings each time. If I create a project on my co2 ...
- LightBurn
- fiber laser
- CO₂ laser
Cruise Wang1.3K51Galvo stops filming, What should I do?
My Omtech 50 W fiber will not frame. It used to. Still cuts fine but need to be able to position material. I feel this is in my settings. Can someone share their settings so I can try and get this wor...
- LightBurn
- fiber laser
- laser cutting
Tim Johnson1.3K50Höhe zwischen den Schnitten
Kann mir jemand helfen, ich habe einen Faserlaser mit Steuerung ,,RDC6563FG mit Fuji Alpha smart Plus " schneide überwigend Edelstahl 1mm Bleche. Das Problem ist von Schnitt zum nächsten Schnitt, fähr...
- coordinate axis
- RDC6563FG
- fiber laser
- control system
- RuiDa
aO5ZCpeb1.3K20What kind of control system is required for non-metallic material laser cutting
The range of non-metallic materials is very wide, and there are various processing methods. However, in the face of high-power lasers, it is usually only necessary to consider the optical properties o...
- fiber laser
- control system
- CO₂ laser
- laser cutting
Cyril1.4K10What kind of laser control system is used for laser cutting of polymer materials
Polymer materials, also known as polymer materials, are materials composed of polymer compounds as the matrix and other additives. There are many types of polymer materials, which can be divided into ...
- fiber laser
- control system
- CO₂ laser
- laser cutting
Miller1.7K00Common faults and solutions of fiber lasers
1. Unstable laser output Unstable laser output is one of the common faults in fiber lasers, which may lead to unstable processing quality or even processing failure. Possible reasons: (1) Laser lens c...
- fiber laser
- laser cutting
Andre J1.3K10RDC6563FG-LITE
Hi, I have a RDC6563FG-LITE and the Manual is only in chinese and has not been translated to EN, I have used a translating service to translate the PDF but the translation is lacking and I have some ...
- coordinate axis
- RDC6563FG-LITE
- fiber laser
- control system
- RuiDa
Juan Barkhuizen1.6K41Ruida RDACC-Fiber-V2.0
Hello dear Ruida team, i got the Ruida RDACC Fiber Module V2.0 from you. I activated the calibration menu during the dry running test. Here the voltage was displayed to me and then the module switc...
- fiber laser
- control system
- RuiDa
Gewindestange1.2K40Laser cutting sheet metal technology
In order to swiftly heat the material to the vaporization temperature, evaporate it, and produce holes in it, laser cutting involves the employment of a high-power density laser beam. The material is ...
- fiber laser
- CO₂ laser
- laser cutting
David1.4K10Cloudray JPT M7 60W MOPA Fiber Laser FBLI-B-LV4 Drivers not working
Order/Invoice ID: Available upon request Issue Product Name: Cloudray JPT M7 60W MOPA Fiber Laser Issue Description: No included drivers shipped with this unit, nor downloaded from the Cloudray site w...
- fiber laser
Tory1.4K10
fiber laser
62
Onderwerpen2
VolgersWacht op antwoorden
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.