Hello,I also have the problem that when transferring data I get the error message that an error occurred while sending (the device may be busy or stopped).In the forum I found a post that you can try to set "enable DTR signal" in the device settings.Where exactly can I select this in the device settings?

JOST

2024-12-05

642

1

0

Power failure1. Check if the power cord is securely plugged in;2. Check if the power cord is damaged;3. Check if the power supply is working properly.Laser malfunction1. Check if the laser is working properly;2. Check if the laser cable is securely plugged in;3. Check if the laser cable is damaged.Other reasons1. Check if the light tube has expi...

Clarence

2024-12-04

705

0

0

Multiple methods can be used to avoid the problem of laser welding undercutting, such as optimizing process parameters, reducing welding speed, optimizing plate edges, etc.Reasons for laser welding edge biting problemThe problem of laser welding undercutting refers to the phenomenon of excessive melting and compression at the welding point during ...

Smith

2024-12-02

734

2

0

Problem OverviewThe inability of laser cladding powder to hang refers to the phenomenon where the powder cannot uniformly adhere to the substrate during the laser scanning process, resulting in phenomena such as powder falling off. This phenomenon not only affects the processing effect, but may also damage the equipment.Root cause analysis of the...

Cyril

2024-12-03

623

1

0

Parameter adjustment skillsIt is very important to set and adjust parameters correctly when performing handheld laser welding. Here are some parameter adjustment techniques:1. PowerHandheld laser welding machines are usually equipped with adjustable focal lengths. During the welding process, the focal length can be adjusted according to the condi...

Darren

2024-12-03

620

0

0

With the rapid development of laser cleaning technology, it has gradually entered people's lives due to its unique advantages such as low damage to the substrate material, high cleaning accuracy, zero emissions, and no pollution. There is no doubt that applying laser cleaning technology to the cleaning of dirt on metal surfaces has a very broad pro...

Kevin

2024-11-29

747

2

1

UV laser is a special type of laser with a short wavelength, concentrated energy, and short pulse frequency. The wavelength range of this laser is between 200~400nm, and its high-energy photons can break chemical bonds on materials at the molecular level, thereby achieving the effect of separating and breaking materials. These characteristics make ...

Williams

2024-12-02

769

0

0

1. Self melting alloy powdercharacteristic:Containing B and Si (functions: deoxidation, slagging).Substrate adaptability.It can be widely used in various materials including carbon steel, alloy steel, stainless steel, and cast iron, but it is not suitable for steel with high sulfur content because the sulfur in the steel will form a low melting poi...

Aaron

2024-11-29

714

0

0

I have an S1 and am currently using Lightburn 7.03. In previous forums, there was lengthy discussions about this issue and last May, it was posted that the new Lightburn version 7.0 would fix it. I cam using the current version, and my S1 is still cutting triangles when I put a square around a design to be cut. It finishes cutting the design and th...

Silvano

2024-11-21

850

5

0

To improve the efficiency and stability of laser welding, the following aspects can be considered and operated:1、 Equipment selection and optimizationChoosing high-power lasers: Higher power output can significantly accelerate welding speed, thereby improving overall efficiency.Equipped with advanced optical systems: can effectively ensure beam qu...

Darren

2024-11-27

751

1

0

Offset - Lightburn 1.7.03The operation is different for 1 mm or 0.15mm, the generated images are not independent.The external direction generates 2 shapesThe inner direction does not generate anythingThe direction Both generate 2 shapes that are not independent for small values 0.15mm.

Roderick

2024-11-21

842

4

0

Glass is a material with high hardness, and traditional mechanical carving methods are often difficult to use. However, as a high-precision and high-efficiency burning method, laser can overcome this difficulty. Laser engraving of glass can not only achieve high-precision engraving effects, but also preserve the properties and quality of the glass ...

jessie

2024-11-26

657

1

0

let’s say I have 2 parallel curves that are close to each other… I would like to select the nodes of one of the 2 curves without also taking the nodes of the other.how do I do it?if I box the nodes I also intercept the nodes of the other curve and I haven’t found a button to select or exclude individual nodes so as to form a group that I can move a...

Durell

2024-11-18

649

6

0

UV laser marking machine is a high-precision and high-speed laser marking equipment widely used for surface marking of various metal and non-metal materials. However, in practical use, there may be a problem of decreased laser power. This article will analyze the reasons for the power drop of ultraviolet laser marking machines and propose correspon...

Vasili

2024-11-25

643

1

0

On my rotary setup all my laser engravings work properly except for any circular shapes when done in the “line” setting.“Fill” setting works just fine as you can see in the picture with the logo.When i do shapes like an square (10x10cm) it also works just fine.Any suggestions?thanks in advance.

JOST

2024-11-19

783

4

0