Recently, when I try to engrave using my Xtool D1 pro, the engraving is way off. When I frame the job, everything looks fine. But once I start to engrave, the laser moves roughly 1.5 inches to the left. This has happened consistently over the last month. I’ve managed the engraving by manually adjusting the starting point of the laser.Today, I trie...
2024-12-06215201、 Motor burnt outOne of the common faults of brushless DC motors is motor burnout. Possible reasons include overvoltage, overload, overheating, etc. If the motor is found to be burnt out, it is necessary to replace the motor and check whether the relevant circuits are working properly.2、 Controller malfunctionThe controller is a very important c...
2024-12-0724910The laser stops firing in the meddle of the job but the head doesn’t stops. When that happens, the head eventually stops, moves back and tries to keep engraving where it stops. The problem with that is that when that happens it never restart in the same position, making a really noticeable line along the path. That line is just shifted from the “or...
2024-12-0724710Introduction to Laser CladdingLaser cladding is a process of partially melting the surface of a material by irradiating it with a laser beam, spraying powder or wire onto the melted surface to generate a new surface layer. It can be used to repair damaged components, improve surface hardness, enhance surface performance, etc.Factors affecting the...
2024-12-0623000Hello,I also have the problem that when transferring data I get the error message that an error occurred while sending (the device may be busy or stopped).In the forum I found a post that you can try to set "enable DTR signal" in the device settings.Where exactly can I select this in the device settings?
2024-12-05218101、 Poor lubricationPoor lubrication is one of the main reasons for gear pitting corrosion. When the viscosity of the lubricating oil is insufficient or the pressure resistance is poor, it will weaken the lubrication and cause pitting corrosion on the friction surface. In addition, excessive impurities in lubricating oil can also affect the lubricat...
2024-12-0521300Fault performanceWhen the chiller of the laser cutting machine malfunctions, the following symptoms may occur:1. The chiller cannot start or stop. This may be caused by power failure, motor failure, water pump failure, and other reasons.2. The chiller produces excessive noise during operation. This may be caused by water pump failure, fan failure, ...
2024-12-0426010Power failure1. Check if the power cord is securely plugged in;2. Check if the power cord is damaged;3. Check if the power supply is working properly.Laser malfunction1. Check if the laser is working properly;2. Check if the laser cable is securely plugged in;3. Check if the laser cable is damaged.Other reasons1. Check if the light tube has expi...
2024-12-0421200Multiple methods can be used to avoid the problem of laser welding undercutting, such as optimizing process parameters, reducing welding speed, optimizing plate edges, etc.Reasons for laser welding edge biting problemThe problem of laser welding undercutting refers to the phenomenon of excessive melting and compression at the welding point during ...
2024-12-0224820Problem OverviewThe inability of laser cladding powder to hang refers to the phenomenon where the powder cannot uniformly adhere to the substrate during the laser scanning process, resulting in phenomena such as powder falling off. This phenomenon not only affects the processing effect, but may also damage the equipment.Root cause analysis of the...
2024-12-0328510Parameter adjustment skillsIt is very important to set and adjust parameters correctly when performing handheld laser welding. Here are some parameter adjustment techniques:1. PowerHandheld laser welding machines are usually equipped with adjustable focal lengths. During the welding process, the focal length can be adjusted according to the condi...
2024-12-0323200With the rapid development of laser cleaning technology, it has gradually entered people's lives due to its unique advantages such as low damage to the substrate material, high cleaning accuracy, zero emissions, and no pollution. There is no doubt that applying laser cleaning technology to the cleaning of dirt on metal surfaces has a very broad pro...
2024-11-2923221UV laser is a special type of laser with a short wavelength, concentrated energy, and short pulse frequency. The wavelength range of this laser is between 200~400nm, and its high-energy photons can break chemical bonds on materials at the molecular level, thereby achieving the effect of separating and breaking materials. These characteristics make ...
2024-12-02237001. Self melting alloy powdercharacteristic:Containing B and Si (functions: deoxidation, slagging).Substrate adaptability.It can be widely used in various materials including carbon steel, alloy steel, stainless steel, and cast iron, but it is not suitable for steel with high sulfur content because the sulfur in the steel will form a low melting poi...
2024-11-2923700Reasons for unstable power of synchronous motors1. Poor circuit connection: The circuit connection of synchronous motors, such as poor circuit connection and poor contact of contacts, can lead to unstable motor power.2. Mechanical load changes: The operating environment and load changes of synchronous motors can affect the output power of the moto...
2024-11-2823910
- Geen gegevens
Nederlands
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski