I just installed my LightBurn camera, got it calibrated and it works fine. But, When I first open Lightburn and go to the Window menu, select camera control, it does not open. I’ve selected, unselected several times and still doesn’t work.Help!, please.
2023-12-2921510HiSince a few days, Lightburn switches off the positioning laser on my iKier K1 when I run framing. I believe this has been since 1.4.04 release. Was there any change or do you have any idea how to fix this?
2023-12-2920410I have orders for some coasters. I’m using a 10w laser. I select the coaster drawing and I unlocked the size. When I input the size in both with and height. I lock the paddle lock. I then move the object with my mouse. Why does the size change?Also when I select the object I’m engraving and click on FRAME, I have to reselect the same o...
2023-12-2918510The first Chanelink Halloween/Christmas series of activity--Laser Processing Art Carnival has finished the solicitation. There was a great response to the event and a large number of wonderful works were received, each one of which was excellent.The Chanelink team has selected the award works based on many dimensions, such as technological ...
2023-12-2925214I have seen others add 2 solenoids to CN1 so they have low pressure and high pressure air assist. They use pin 6, +24 for the + connection on the solenoids and then pin 5, wind for the - side of one solenoid followed by pin 4, status for the - connection on the other solenoid. Why is pin 1, - not used and are these connections correct?...
2023-12-2922920Chillers are a common industrial refrigeration equipment widely used in production processes in various industries, such as electronics, chemical, mechanical, pharmaceutical, and more. Its main function is to quickly dissipate the heat generated by industrial equipment, maintain the normal working temperature of the equipment, and thus ensure the n...
2023-12-2819510How often should I clean the lens of my diode laser and how do I know when to clean it?
2023-12-2824010I have purchased the Lightburn 5mp-150 with Aspect 1.333. The Camera selection help table indicated that the minimum mounting 8.75". I have the camera mounted at 11’ from the laser bed and it will not capture the dot pattern. It will capture the same pattern when I raise the camera to 12" or higher.I do not have the space to keep the camera a...
2023-12-2824310I’m just starting my new venture. How do you set up or where do you get your line mode color square usually located at the bottom of lightburn users screen. Thanks for your help. I have been in the computer world for years but am stumped on this little question.
2023-12-2724110Hi and thank you for your time and suggestions.I’m a newbie to laser and Lightburn.Can you please suggest some of the best online box makers that I as a newbie will easily get a hold on? I’ve done some searching and some seem very easy but, for some reason have lower ratings.Thanks so long.
2023-12-2726010My computer crashed while engraving earlier. Image had a 1 hour 15 minute time estimate. Same engraving this morning was close to that estimate. Trying to burn image this afternoon, estimate is not 1 hour 40 minutes. Laser head doesn’t change speeds when changing settings while doing test burns.Any ideas on what setting(s) need to looked at?
2023-12-2721910In the early automation industry, motion control was mostly pulse control and analog control. Later, CANopen was developed, and various Ethernet buses emerged, such as EtherCAT, PROFINET, POWERLINK, SercosIII, RTEX, and so on.Why is EtherCAT developing so rapidly both globally and in China now, mainly reflected in the following five points:...
2023-12-2620110May I ask if you are planning to use a laser displacement sensor to scan the parts, and then use a servo motor with a grinding wheel to follow the contour of the parts for polishing? How should you configure the hardware?
2023-12-2623210I was wondering if anyone has successfully cut anything with the 5 watt creality laser module attachment not the table and laser, the actual unit that attaches to my 3d printer. If so what speed and how many passes?
2023-12-2620710Hello all. I hooked up my Ortur Extension to engrave longer pieces and changed my settings but when I hit Frame the laser goes to about the middle right of the project and just stops. Any suggestions? Seems to be only this particular project.
2023-12-2622210
- 데이터 없음
한국어
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski