I am hoping I will be able to import vector artwork from exterior programs to MillMage and I was wondering if that will be possible? I currently have Affinity Designer 2 and Inkscape- I am a graphic designer and they are easy for me to use. Or will it be better to do all the vector work in MillMage, when it comes out? Will MillMage be able to have ...

Erdogan

01-18

1.1K

2

0

Hi All,I recently updated to v1.7.04 from very old version. I’m setting up a diode laser machine (that was working on that old version) and have upgraded the controller to an MKS SBase I had lying around), running Smoothieware.What happened to the “Laser Control Commands” in Device Settings? I’m struggling to get the laser to fire properly.It’d a...

Narrator

01-16

1K

4

0

The reason for the sudden failure of laser cutting machine1. Laser malfunction. Laser is the core component of laser cutting machine. If the laser malfunctions, it will cause the laser cutting machine to malfunction.2. Optical path malfunction. The optical path is the channel through which the laser cutting machine transmits laser and performs cutt...

Vasili

01-20

1K

0

1

1、 Reason for the problemIn the process of laser cutting, if the cutting line is too small or the laser power is too low, there will be a problem of non closure. In addition, if the cutting speed is too fast, this problem is also prone to occur. In addition, the material of laser cutting can also affect the closure of the cutting, and if the materi...

Christian

01-18

976

0

0

I have a image that i duplicated a few time to make a longer image. I am trying to make this image fit into a circle to make this image round.I can do text fine. But not images. If there is away, please let me know. Thanks.

RTP

01-13

920

8

0

Probably is a dumb question, but is there a simple way if stopping knives on the laser bed from falling inwards when u take honeycomb in and out. Had to replace my knives and holder. Have tried hot gluing tabs on ends where the knives seat but they fall off after a week ot so.

Ruddy

01-15

1.2K

3

0

I have a two trees TTS20 Pro, I have it set up to home at front left as per the instructions in my lasers manual, but the machine keeps trying to home at back left and when doing so it slams into the top and side walls and makes a terrible grinding sound.All images are engraved upside down to what is shown on LightBurn.I have tried deleting my lase...

Roderick

01-10

1.1K

5

0

With the development of the industrial industry, brushless DC motors, as a commonly used type of electric motor, have become increasingly widely used due to their high efficiency, high speed, and low noise. At the same time, their equipment maintenance and upkeep are also receiving more attention. So, what are the common faults of brushless DC moto...

Cyril

01-15

1.1K

0

0

In the daily operation of laser equipment, the constant emission of light is a common and difficult problem to solve. It not only affects the quality of the product, but may also increase the maintenance cost of the equipment. Faced with the problem of continuous light emission, it is urgent to quickly and accurately diagnose the location of the fa...

Abel

01-10

1.2K

3

3

Possible reasons for the sudden stop of laser cutting1. Insufficient power: Insufficient power of the laser cutting machine may cause a sudden stop during the cutting process. This may be caused by a problem with the laser pump.2. Abnormal optical path: The deformation or contamination of mirrors in the laser optical path may also cause the laser c...

Payson

01-13

1.1K

1

2

When I have a window open and connected to the laser and working.Why don’t I get oneconnection with to the laser from the second or third or fourth window . I have to close the first window to regain connection with the laser againI would like to changebetween the windows for burning withoutrestart LB

Silvano

01-09

929

2

0

Have: Neje Max 3 and latest release of LightburnI have problems with the coordinates in Lightburn not matching my Neje Max 3.When I have a drawing in Lightburn that is within the “Working Area”, but close to the edge and I select “Start” I get an error message “out of bounds”Looking for help to calibrate so that Lightburn and the laser match.My w...

LWE

01-08

837

3

0

The occurrence of ghosting or blurriness during engraving operations on laser marking machines may be due to various reasons. To solve this problem, it is usually necessary to follow the following steps to check and adjust:1. Check the optical system:Confirm whether the laser and its optical components (such as lenses) are clean, as dust and stai...

Miller

2024-12-27

1.1K

1

3

1、 The lifespan of the nozzle has expiredThe service life of the laser cutting machine nozzle is limited, usually around 500 hours. If it exceeds the service life, both cutting quality and economic benefits will be affected, and a new nozzle needs to be replaced.2、 Damaged nozzleThe laser cutting machine nozzle is prone to damage, such as nozzle ...

Keegan

01-08

858

1

1

1. Fault phenomenon one: The laser marking machine does not produce laser lightThe troubleshooting steps are as follows:Power supply inspection: Firstly, it is necessary to confirm whether the power supply wiring of the laser is correct, including whether+24V and GND are reversed, and whether the ground wire is properly grounded. Test whether the...

Terrelle

01-09

1.2K

1

2