Master, why do some encoders of servo motors need to be zeroed when they are removed or replaced. What kind of encoder should be zeroed and what kind of encoder should not be adjusted.
2023-03-0648210Now many motor factories have begun to use motor assembly lines to produce motors, which not only greatly improves the efficiency and saves a lot of labor costs, but also is better than manual assembly. It is quite convenient to match a good detection system. So what are the principles for the layout of motor assembly lines as a manufacturer of mot...
2023-03-0634600High-speed laser cladding is a fast laser surface treatment technology. Its process characteristics are good cladding quality, high speed, low cost, and certain market competitive advantages. Improper selection of process parameters for high-speed laser cladding will lead to poor forming quality and easy deformation.The key parameters invol...
2023-03-0641500I had similart probblem before. There must be a setting enabled addlling this kerf and I donmty know where to disable it. As you see in pics I’ve uploaded itrs adding an offset or kerf again . Can you tell me where to turn this off and how I remove it now with this project.
2023-03-0449510Hi friends! Please see attached pic, there is a visible jittering while the laser head changes direction from the vertical to horizontal movement, immediately after the turn, everything ok on slow speed but appears on medium and high, any suggestions how to fix it please? ThanksPS: could it be because of the table with the laser slightly unstable...
2023-03-0441310with lightburn active, and Ortur Master 3 on, I send a cut path to the laser, this is what i get “Trouble sending data to laser, Machine maybe busy or paused” I’m just getting started. Needhelp.
2023-03-0432110I’ve gone through the process in full from the official installation page, and it’s still not working.That was an attempt at the .run file, terminal looks like it went, but nothing to actually start it from.I then navigate to the folder it’s referencing, set it to be trusted, icon shows, but nothing happens when I double click it...
2023-03-04372103D simulation of how the wake behind the electron beam (purple) and the light pulse (blue and red stripes) surf behind it. The plasma wake shows no electrons in alternating yellow, and green shows the peak of electron density. When the light pulse is located on the boundary, it can continuously obtain energy - the trick is to keep it there. Source:...
2023-03-0429610The servo motor is used with the reducer, such as the planetary reducer. The reducer has a reduction ratio. The servo motor outputs the specified speed. After the reducer decelerates and increases the torque, will the speed accuracy of the output shaft of the reducer be improved? Or does the reducer affect the speed accuracy of the servo motor? Is ...
2023-03-0447910The reason why the motion control card cannot be connected
2023-03-0445810The servo motor moves up and down, has an origin, and moves up and down in the process of returning to zero. Each time, the value of moving up and in place is periodic, pulse signal, what is the situation.
2023-03-0447610In servo torque mode, the speed limit value is controlled by analog quantity, and the torque limit signal is used to achieve the purpose of screwing.At present, the problem is: when the torque limit signal is output, you want to judge whether it is screwed in place. How do you realize this working condition? What is the convenient way?In addition, ...
2023-03-0441310The response speed is a very important index to measure the motion control system. In addition to the response speed, there are also some important parameters related to product quality and production efficiency:1. The number of axes supported by the controller and the performance of multi-axis linkage and cooperation.2. Accuracy of...
2023-03-0433200Which control mode is generally used for servo press?
2023-03-0341310Siemens servo homing failed. I am the disc homing. After I turn back, the zero position and the last homing position cannot coincide. The known reduction ratio is 1:20. Please tell me how to deal with it.
2023-03-0326610
- データがありません
日本語
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski