Italiano

An efficient femtosecond pulse amplification technique for extracting the maximum stored energy in fiber laser amplifiers

505
2024-11-13 11:55:15
Vedi traduzione

The well-known journal Optica published a paper in November 2024 titled "Near complete extraction of maximum stored energy from large core fibers using coherent pulse stacking amplification of femtosecond pulses"The authors of the paper were the University of Michigan, Lawrence Berkeley National Laboratory, Peking University, and the German Institute of Synchrotron Radiation.

The specific technique is to use a cascaded "GTI" (Gire Tounois interferometer) method to synthesize 81 amplified pulses together in the time domain. The technical difficulty that needs to be overcome is to control the phase and amplitude of each pulse to achieve coherent synthesis. The core femtosecond light source is a 1 GHz repetition rate femtosecond fiber laser, developed by Professor Zhang Zhigang's group at the School of Electronics, Peking University.

The author of the paper has demonstrated using the aforementioned techniques that, with a continuous pump of 100 W and a repetition rate of 2 kHz, nearly 10 mJ of amplified pulse energy can be extracted, far exceeding the energy output of conventional large mode area fiber amplifiers, which can reach less than 1 mJ. The extraction efficiency is close to 90%.

This efficient time-domain pulse synthesis technique can greatly improve the efficiency of pulse synthesis and reduce the number of amplifiers used for spatial synthesis.

Although the repetition rate and pulse energy obtained from this experiment are not yet high, this technology demonstrates the potential to generate femtosecond strong laser pulses with Joule level pulse energy and repetition rates above 10 kHz. It may provide a light source for studying strong field physics and particle accelerators under extreme conditions, as well as for generating secondary radiation.

Figure 1 shows the efficiency of pulse energy extraction in a fiber amplifier independent of core diameter under nonlinear confinement. Figure 1 indicates that the pulse extraction efficiency can only approach 100% of the amplifier's stored energy when the pulse is broadened to 100 ns


Figure 2 shows a schematic diagram of a composite GTI cavity, where 81 incident laser pulses are coherently superimposed in four large loop cavities to form 9 pulses; Then coherently superimpose them into one pulse in four small cavities


Figure 3: Photo of the Composite GTI Chamber Experimental Device


Figure 4 shows the pulse waveform and spectrum of the coherent synthesized pulse with an energy of 3 mJ and a width of 313 fs

Source: Yangtze River Delta Laser Alliance

Raccomandazioni correlate
  • Researchers have discovered a new method to improve the resolution of laser processing

    Customized laser beams focused through transparent glass can generate a small dot inside the material. Researchers from Northeastern University have reported a method of using this small spot to improve laser material processing and increase processing resolution.Their research results are published in the journal Optics Letters.Laser processing, like drilling and cutting, is crucial in industrie...

    2024-03-28
    Vedi traduzione
  • The research team developed additive manufacturing (AM) technology based on hydrogel injection, and related research was published on Nano Letters

    It is reported that the research team of California Institute of Technology has developed an additive manufacturing (AM) technology based on hydrogel injection, which uses two-photon lithography technology to produce 3D metal with a characteristic resolution of about 100 nm.The relevant research is published in the journal Nano Letters, titled 'Suppressed Size Effect in Nanopillars with Hierarchy ...

    2023-09-25
    Vedi traduzione
  • Scientists are using lasers to create lunar paving blocks

    Original Hal Bowman 9000 Scientific RazorThe 3 kW laser power output on a 45 mm laser spot consolidates the interlocking structure within the EAC-1A powder bed. Source: Jens Kinst, BAMBy using lasers to melt lunar soil into stronger layered materials, it is possible to build paved roads and landing pads on the moon, according to a concept validation study in a scientific report. Although these exp...

    2023-10-14
    Vedi traduzione
  • MKS Instruments will build a factory in Malaysia

    Recently, American semiconductor equipment manufacturer MKS Instruments announced plans to build a factory in Penang, Malaysia to support the production of wafer manufacturing equipment in the region and globally. This development plan will be divided into three stages to build a new factory, and it is expected to break ground and start construction in early 2025.Why choose to build a factory in M...

    2024-06-26
    Vedi traduzione
  • Significant progress has been made in the manufacturing and measurement of EUV lithography light source collection mirrors

    Summary:To filter out infrared light from the driving light source in the extreme ultraviolet lithography (EUVL) light source system, a rectangular grating structure needs to be fabricated on the surface of the collection mirror. However, the collection mirror grating usually undergoes deformation during the manufacturing process, resulting in a decrease in filtering efficiency. The process errors...

    04-02
    Vedi traduzione