chanelink logo
CHANELINK
Italiano

TSMC's first European wafer fab receives € 5 billion subsidy for construction

200
2024-08-26 13:41:59
Vedi traduzione

Recently, TSMC held a groundbreaking ceremony for its first European 12 inch wafer fab. It is reported that the European Union has approved Germany to provide 5 billion euros in subsidies for the factory.

It is understood that TSMC's 12 inch wafer fab is located in Dresden, Germany and is called "European Semiconductor Manufacturing Company (ESMC)". In August 2023, TSMC announced a partnership with Bosch, Infineon, and NXP to jointly invest in the establishment of ESMC. TSMC holds a 70% stake and is responsible for operations, while Infineon, NXP, and Bosch each hold a 10% stake, with a total investment of approximately 10 billion euros.

The wafer fab is expected to introduce 28/22 nm planar complementary metal oxide semiconductor (CMOS) technology and 16/12 nm fin field-effect transistor (FinFET) processes, with an initial monthly production capacity of approximately 40000 12 inch wafers. According to the planned construction schedule, the factory will start construction in the fourth quarter of 2024, with equipment expected to enter the factory in the third quarter of 2026 and mass production starting as early as the fourth quarter of 2027.

It is worth noting that at the foundation ceremony, EU Executive Committee President von der Leyen announced that the EU has approved to provide 5 billion euros of subsidies for Dresden wafer factory.

In fact, in addition to building factories in Germany, TSMC is also investing heavily in setting up factories in the United States and Japan. However, industry insiders point out that TSMC's expansion overseas will face a series of challenges, including high operating costs, labor shortages, cultural differences, and more. For example, the German Silicon Valley Association reminds that the German labor union has a strong and tough attitude, which is one of the challenges that TSMC must overcome.

Source: Yangtze River Delta Laser Alliance

Raccomandazioni correlate

  • French silicon optical company Scintil realizes the integration of III-VI DFB lasers and amplifiers with standard silicon optical technology

    Recently, French silicon photonics company Scintil Photonics announced an exciting collaboration, successfully integrating III-V-DFB lasers and amplifiers with standard silicon photonics technology in the production of Israeli semiconductor company Tower Semiconductor. This milestone collaboration marks a crucial step for Scintil in strengthening its supply chain, bringing new possibilities to com...

    2024-03-05
    Vedi traduzione

  • Coherent Company Launches Industry's First 1200 mW Pumped Laser Module for Optical Amplification in DWDM Networks

    Coherent Corporation, the leader in erbium-doped fiber amplifier pumped laser technology for deployment in optical networks, announced today the launch of the industry's first pumped laser module in a 10 pin butterfly package with an output power of 1200 mW.The rapid development of optical communication technology is reaching the theoretical limit of fiber capacity and driving the expansion of tr...

    2023-09-22
    Vedi traduzione

  • The technological iteration route of automotive millimeter wave radar chips

    The rapid development of intelligent cars and autonomous driving technology has made millimeter wave radar inconspicuous, and the widespread application of millimeter wave radar has driven the technological evolution of MMIC.From the expensive gallium arsenide (GaAs) process in the early days to the mainstream CMOS and SiGe processes today, and then to the future promising FD-SOI process, the cont...

    2024-12-07
    Vedi traduzione

  • GOLDEN laser die-cutting machine will be exhibited at UPAKEXPO 2024

    At the UpakExpo 2024 exhibition to be held in Moscow at the end of January, Chinese company Golden Laser will showcase for the first time two laser die-cutting machines focused on the printing, labeling, and packaging markets in Russia.The Golden Laser LC350 is a web machine designed to handle labels printed on digital and flexographic printing machines. It can cut, die cut, and kiss cut paper, pl...

    2024-01-12
    Vedi traduzione

  • Significant progress has been made in the manufacturing and measurement of EUV lithography light source collection mirrors

    Summary:To filter out infrared light from the driving light source in the extreme ultraviolet lithography (EUVL) light source system, a rectangular grating structure needs to be fabricated on the surface of the collection mirror. However, the collection mirror grating usually undergoes deformation during the manufacturing process, resulting in a decrease in filtering efficiency. The process errors...

    04-02
    Vedi traduzione