Italiano

The United States is expected to use "AI+lasers" to deal with space debris in the future

269
2023-10-20 13:51:14
Vedi traduzione

Due to the increasing threat of space debris in low Earth orbit around the Earth, space agencies around the world are becoming increasingly concerned about this. According to a new study funded by the National Aeronautics and Space Administration (NASA), it may be possible to send space debris that may be at risk of colliding with orbiting spacecraft to safer orbits through a laser network deployed in space in the future, the US "Space" website said on the 19th.

The report states that space debris has an increasing impact on the safety of spacecraft in various countries. When Amazon launched two internet prototype satellites on the 6th, it was forced to delay the launch for 6 minutes to avoid colliding with space debris.

In July of this year, due to the same reasons, the launch of India's historic "Lunar Ship 3" probe was also forced to be postponed. Although space debris has been a concern for decades, efforts to address this space debris have only recently truly begun to get back on track. The idea proposed by the Space Systems Warfare Research Laboratory at the University of West Virginia is to install artificial intelligence (AI) controlled space-based lasers on satellites or other specialized platforms for monitoring space debris. When a space debris is suspected of colliding with valuable space assets such as the International Space Station or satellites, laser pulses are used to push them into safer orbits.

According to the report, the statement released by the laboratory states: "Our goal is to develop a reconfigurable space-based laser network and AI algorithms. These algorithms will make this network possible and maximize its benefits." The plan has received funding from NASA and is still in its early stages. The ultimate goal is that the system will decide on which lasers to use to target a certain space debris, At the same time, ensure that the generated trajectory does not collide.

It is said that measuring the risk level of space debris is quite difficult because not every object in orbit can be tracked. According to data from the European Space Agency, the radar system on the Earth's surface is currently tracking approximately 34600 space debris, but there may still be 130 million fragments in orbit that cannot be accurately detected or tracked due to their small size. The report states that although the mass and volume of these space debris are small, their speed is fast enough to pose a threat to orbiting satellites or spacecraft.

Previously, countries had a preference for clearing space debris, but whether it was using high-strength materials to create "space debris nets" for salvage or using high-energy lasers for burning, there were limitations. In contrast, using space-based lasers to process small space debris may be more practical, as they can be sent into predetermined orbits using laser pulse irradiation, with relatively low power requirements for lasers. The report states that using multiple lasers can more effectively alter the trajectory of space debris, which "cannot be achieved by a single laser".

In March of this year, NASA released a report showing that space-based lasers are not affected by weather compared to ground based lasers. The report states that this AI powered space cleaning system not only has cost advantages, but its precise tracking ability for space debris also helps improve the safety of space launches.

Source: Global Times

Raccomandazioni correlate
  • Which automotive parts can use laser soldering technology

    Laser soldering is widely used in the manufacturing of automotive parts. Here are some common automotive parts that can be welded using laser soldering:Automotive electronic control systemEngine Control Unit (ECU): The engine control unit is the "brain" of the car engine, which receives signals from various sensors and controls the operation of the engine based on these signals. Laser soldering ca...

    02-10
    Vedi traduzione
  • Research has shown that patterns on crystals can double the optical sensitivity of photodetectors

    Scientists from the Institute of Automation and Control Process at the Far East Branch of the Russian Academy of Sciences described the changes on the surface of monocrystalline silicon during laser processing. The author of this study placed the crystal in a methanol solution and applied a laser pulse lasting one thousandth of a second to the sample, with a pulse count ranging from five to fifty ...

    2024-04-01
    Vedi traduzione
  • Optoma Launches Environmentally Friendly Short Focus Laser 4K Ultra High Definition Home Entertainment and Gaming Projector

    Ranked first in the global and American projection technology fields with 4K UHD and DLP ® The brand Optoma has launched Optoma UHZ35ST, a 4K ultra high definition home entertainment and gaming projector that follows the popular UHD35STx with a short focus laser. With its external power supply and various functional upgrades, UHZ35ST provides higher reliability, portability, and energy e...

    2023-09-19
    Vedi traduzione
  • Each unit of metamaterials used for simulating optical calculations is smaller than the wavelength of the light they are designed to manipulate

    The new architecture based on metamaterials provides a promising platform for constructing large-scale production and reprogrammable solutions that can perform computational tasks using light.The idea of simulating computers - a device that uses continuous variables instead of zero sum ones - may evoke outdated machinery, from mechanical watches to bomb sight devices used in World War II. But emer...

    2024-03-30
    Vedi traduzione
  • Trends and Reflections on the Laser Industry in 2025

    In 2024, the laser industry will still reach new heights, although some predicted concerns have been fulfilled! From beginning to end, the development path of the manufacturing industry has been full of uncertainty, but as time passes and we enter a new year, new technologies continue to emerge like mushrooms after rain.In 2025, practitioners in the laser and manufacturing industries still face ma...

    01-02
    Vedi traduzione