- Non risolto
The power indicator light of my controller is not illuminated, RDC6332NM
It's strange. Today, when I tried to operate the machine, the green power indicator light on the controller didn't light up at all. The device showed no signs of power-on startup and was in a complete...
- power supply
- RDC6332NM
- control system
- laser cutting
- RuiDa
- 2 utenti hanno risposto
288 - Risolto
Help! The panel of the RDD6584G system crashes frequently during work
I posted a message some time ago and would like to thank the experienced technician for their prompt response. I have been operating the RDD6584G control system for two weeks now. Today, while perform...
- power supply
- RDD6584G
- control system
- RuiDa
- 2 utenti hanno risposto
266 - Non risolto
RDC6332NM, abnormal voltage at the laser control signal port
Hello everyone, the issue from last time has been resolved. However, I encountered a new problem today. My RDC6332NM control system is experiencing an abnormal voltage at the laser control signal port...
- power supply
- RDC6332NM
- control system
- laser cutting
- RuiDa
- 2 utenti hanno risposto
264 What should I do if the CO2 cutting and engraving control system fails to emit light during spot shooting?
When using the CO2 cutting and engraving control system, if you encounter a situation where the spot does not emit light, you can follow the steps below to troubleshoot and resolve the issue: Step 1:...
- power supply
- RDC6442G
- cooling system
- CO₂ laser
- RuiDa
Patrick31500- Risolto
The RDC6442G homes automatically.
My control system uses Ruida's RDC6442G. When I click "start" to process, it will automatically reset to the origin. Is it a problem with the reset button or other firmware? Any suggestions would be g...
- power supply
- RDC6442G
- laser engraving
- laser cutting
- RuiDa
- 2 utenti hanno risposto
300 - Risolto
It's annoying! RDC6563FG press exit to confirm that it does not work
I have been using RDC6563FG all along, and today pressing the exit button does not work. After a period of time, there has been a restart. What should I do?
- power supply
- RDC6563FG
- RuiDa
- 2 utenti hanno risposto
309 What are the vulnerable parts of the laser marking machine that need to be replaced in a timely manner
1、 Laser Laser is the core component of laser marking machine and an important component for generating laser. Normally, the service life is long, but regular cleaning and maintenance are required. If...
- power supply
- laser source
- laser head
- laser marking
Vasili1.3K00Analysis of Fault Causes in Fiber Laser Machine System
Fault in the fiber optic section 1. Fiber breakage: Fiber breakage is the most common situation in fiber laser machine failures, usually occurring in fibers that have been in use for a long time or ha...
- power supply
- fiber laser
Smith1.4K00How to change the phase from 12V to 24V
I have a 5W 12V AtomStack, I want to change the laser for a 20W 24V one. What should I implement to be able to adapt it to the new laser module?
- power supply
- laser source
Cruise Wang1.2K30How to troubleshoot and solve the problem that the laser coding machine's krypton lamp cannot trigger
1. Check the power connection cable Carefully inspect all power connection wires of the krypton lamp, including plugs, sockets, and wiring, for any looseness, detachment, damage, or other issues. If t...
- power supply
- beam delivery system
- laser marking
Gilbert1.6K00How to calibrate the power output of K40 machine
I am sure I am not the only one here that has this happening, most likely with every K40 machine. My machine reaches max output milliamp output at 22-23% output in Lightburn. Would it be possible to c...
- power supply
- LightBurn
Hiroko1.5K40Compatibility issues with parts
In my ongoing quest to get my laser up and running, i have found the manufacturer has discontinued my machine and no replacement parts are to be had. It a Kentoktool JL5 5.5w. I have access to a Laser...
- power supply
- LightBurn
- laser cutting
Ethan1.2K20Controller Fault?
I'm hoping someone here can help me with a problem I'm having. I turned on my system this morning and as the motors homed, they moved normally, when I tried to move the head to a location to start a...
- motion system
- power supply
- control system
- RDC6442S
- RuiDa
RnR Laser1.3K20Ruida RDC6445S Reboot Loop Issue? Help!
Hello, I did a rebuild of a Muse 2D and I got it working fine. In the past 2 weeks it started acting up during cuts. It will randomly reboot. It doesn't happen consistently like after a certain time,...
- power supply
- RDC6445S
- control system
- RuiDa
fCrtGR6q2K21Is it okay to not install a voltage regulator for a 3 kw laser？
Can someone help answer the question？
- power supply
Leon1.5K20
power supply
32
Argomenti4
FollowerIn attesa di risposte
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.