Reasons for Inability to Adjust Camera Exposure in CO2 Visual Cutting Control System
In the CO2 Visual Cutting Control System, such as the RDV6445G and RDV6332M, if issues arise where camera exposure cannot be calibrated, the causes can be attributed to the following two aspects: Cam...
- camera
- CO₂ visual cutting
- RDV6445G
- RDV6332M
- RuiDa
Michael23101Processing method for abnormal display of camera area in CO2 visual cutting control system
When using the CO2 visual cutting control system, if the camera area displays abnormally, the following steps can be taken to troubleshoot and handle it: 1. Check if the camera's USB port is function...
- camera
- USB
- CO₂ visual cutting
- control system
- RuiDa
Spark23801Solution to corner processing problems in CO2 visual cutting control system
During the processing using the CO2 visual cutting control system (models: RDV6445G, RDV6332M, RDC6685U-DFM, RDC6445GZ-DFM-RD), the overall contour is basically accurate. However, if there are abnorma...
- CO₂ visual cutting
- RDC6685U-DFM
- RDV6445G
- RDV6332M
- RuiDa
Gary22300- Risolto
RDV6332M， Uneven black edges on top and bottom during edge lifting
My CO2 visual cutting machine uses the RDV6332M control system. During the edge lifting process, there was an issue of uneven black edges up and down. When the laser head moved, the width of the black...
- CO₂ visual cutting
- RDV6332M
- control system
- laser cutting
- RuiDa
- 2 utenti hanno risposto
246 The mark point of the CO2 visual cutting system is not recognized，what should you do?
During the processing of the CO2 visual cutting system, there may be occasions where the Mark points cannot be identified or are omitted. Generally, the following two steps can be taken to troubleshoo...
- camera
- CO₂ visual cutting
- RDV6445G
- RDV6332M
- RuiDa
Ignativs24201CO2 visual cutting control system, CCD software camera parameter debugging
When using the CO2 visual cutting control system for machining operations, how do I debug the CCD software camera? 1. Enter the camera parameter interface Open the CCD software and click“Camera Param...
- camera
- CO₂ visual cutting
- RDV6445G
- RDV6332M
- RuiDa
Adrian26001- Non risolto
RDV6332M controller,does the Canon 1000d camera require driver installation?
The control system I use for my device is RDV6332M. I have a simple question, do I need to install drivers for the Canon 1000d camera?
- camera
- CO₂ visual cutting
- RDV6332M
- control system
- RuiDa
- 1 utente ha risposto
260 - Risolto
RDC6685U-DFM, the MindVision camera cannot display
My CO2 visual cutting machine uses a Ruida controller, model RDC6685U-DFM, with a MindVision industrial camera. When connected, the camera fails to display.
- camera
- power supply
- CO₂ visual cutting
- RDC6685U-DFM
- RuiDa
- 3 utenti hanno risposto
271 - Risolto
RDV6332M， Camera USB driver not recognized
Today I am operating a CO2 cutting machine, and the control system is RDV6332M. The camera USB driver cannot recognize it. Can anyone help me? How can I solve this problem?
- camera
- USB
- CO₂ visual cutting
- RDV6332M
- RuiDa
- 2 utenti hanno risposto
269 - Risolto
Using RDV6445G, camera exposure cannot be adjusted
I have encountered a new problem again. Using RDV6445G, after connecting the camera, its exposure parameters cannot be adjusted. Manually setting the exposure value is invalid, and the image remains o...
- camera
- CO₂ visual cutting
- RDV6445G
- control system
- RuiDa
- 2 utenti hanno risposto
294 - Risolto
RDV6332M, the webcam is not displaying
My equipment has recently been upgraded with the Ruida CO2 visual cutting series control system, model RDV6332M. However, the network camera is not displaying. I'm not sure what the issue might be. Do...
- camera
- CO₂ visual cutting
- RDV6332M
- laser cutting
- RuiDa
- 2 utenti hanno risposto
295 - Risolto
RDV6445G camera area display abnormal or not displaying
I have a CO2 visual cutting control card, model RDV6445G. When I use it, the camera area displays abnormally or does not display. Even after restarting several times, the problem still persists. Do yo...
- camera
- CO₂ visual cutting
- RDV6445G
- laser cutting
- RuiDa
- 2 utenti hanno risposto
347
CO₂ visual cutting
42
Argomenti18
FollowerIn attesa di risposte
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.