I haven’t used the 2s for a while, and in the interim the software has moved onmy last available upgrade is 1.2.04, but prior actual work had been done on 1.2.01, which was working finei updated to 1.2.04 because trying to use a file created on that version on my desktop machine threw a message suggesting it may not work properly on the old...

Henry

2023-06-13

1.1K

1

0

I have a new machine a Atomstack S10 PRO, Laser is 10-11 Watts max and my problem is that when using Lightburn I have to usemultiple passes to burn through 1mm veneer yet without changing a thing I switch to Laser GRBL and at 100% it will burn through the veneer, I do not understand what if any I am doing wtong? Why is it that both programs are set...

David

2023-06-13

1.1K

1

0

I finally got around to getting my camera set up on my atomstack x20 with y axis extention and the setup and calibration seemed to go smoothly but when I tried to calibrate the alignment it tries to center the test file and puts the overlay centered in the workspace. The Y axis shift won’t move it down far enough to be aligned. I can change t...

Tory

2023-06-13

1K

1

0

I have a problem which is more an annoyance than anything else but wonder if there is a solution.Here I have the visual grid set to the default of 10 and the work area zoomed so the grid legend is clear to read.However if I were to change the zoom, e.g. to zoom into an object or, as in this case, simply click the ‘zoom to frame’ selecti...

Williams

2023-06-12

835

1

0

I own a Thunder Nova 63 Co2 130w laser. A consistent issue I am having is inconsistent results. I place a 1/4" piece of acrylic (material is flat and anchored using pins inserted into honeycomb in the bed, send the file via light burn, and I get a perfect cut. Speed/Power(%) 14/97. At this speed and power the laser usually burns clean through the a...

Smith

2023-06-12

924

1

0

I have an XTOOL laser and it smokes a lot when i am burning a phrase on a cutting board. it smokes my whole house out, it even set off the smoke detectors off a few times. I have it in one of the rooms in my house because it is hooked to my desktop. does anyone have any ideas for keeping the smoke down?

Miller

2023-06-12

1K

1

0

I tend to model on the desktop then save files to my server and open in the shop on the laptop.My laptop/control cpu settings were read from my machine. They appear to be accurate as far as estimated time in the preview and the actual time.But when modeling on the desktop I can see it is nowhere near the actual time. (example: Desktop 1:23min &rarr...

Cyril

2023-06-12

1.2K

1

0

Hello!After installing the extension kit, I luckily stumbled upon a post that I had to update my laser. I now just have installed the 20w upgrade and have been running samples. Do I need to make any changes in Lightburn to reflect this upgrade? Download or settings? I can hang, but I’m not a wiz when it comes to computer programs.Thank you!

Gilbert

2023-06-12

959

1

0

Does anyone know why I am getting these pits, or random holes in the image and around the edge of my image in the glass?Settings are: Xtool D1 20w, Speed 7500, power 75% Bi-directional pattern, Line interval 0.100 mm, lines per inch 254.0, number of passes 1.

Clarence

2023-06-12

1.4K

1

0

My DELL Latitude will not connect to XTOOL D1 PROI am using the correct configuration file but LB cannot find the XTOOL.

Terrelle

2023-06-12

1.1K

1

0

I got my first laser Atomstack x20 a few days ago…and I noticed that It is very noisy and smells not good…So I’d like to connection via wifi because doing job from a distance…I tried to connect via Tibbo Vitual port, but when I command to frame, good job and It is start and then stops working in the actual work command&he...

Liam

2023-06-10

1K

1

0

I assembled the extension kit offered by Ortur that changes the work area from 400mmx400mm to 400mmx800mm. I changed the dimensions of the laser in Lightburn to match the new 400mmX800mm work area. However, the machine will not go outside of the original 400mmX400mm workspace. It gives me the error code:ALARM:2G-code motion target exceeds machine t...

Robert Evans

2023-06-10

910

1

0

I’m using the atomstack x30 and I wanted to check speed engraving things. So I found an image, set my power to 50 and my speed to 10000. It took about 12 minutes (4x5 image). I took the speed up to 15000, and it actually took 14 minutes. If I take it up to 20000 and I get 16 minutes. So I played around with settings until I found that 6500 wa...

Henry

2023-06-10

1.2K

1

0

Hi, Im new to the laser side and ready to start my first print and got it all ready to go except 1 thing. The file im looking to do has all the following and not sure order to do them in. Ive read that inner cut should take place before outer cuts. But what about engraving lines and lettering, should they go before I do the inner cut or after the i...

Jamie

2023-06-10

1.1K

1

0

Hi,I would like to knw if i can replace Atomstack A10 pro 50w head with something more powerful? or is not possible?if yes, what do i need?thank you.

David

2023-06-10

1.2K

1

0