When selecting servo motor specifications, the first step is to evaluate the dynamic performance requirements of the application, such as acceleration, speed, and accuracy. Next, calculate the required maximum output torque based on the load characteristics and consider the safety factor. The size of the motor should be selected based on the instal...

Erdogan

2024-03-26

226

1

1

What are the types of two-phase four wire stepper motor drives?

Vasili

2024-03-25

204

1

0

Gear rack, synchronous belt, and screw are three common transmission methods, each with its unique advantages and disadvantages. The following is a detailed analysis of the advantages and disadvantages of these three transmission methods:Gear and rack:Advantages:a. Accurate transmission, high precision, up to 0.1mm, suitable for high-precision tr...

Nugent

2024-03-25

207

1

0

A stepper motor is an actuator that converts electrical pulses into angular displacement. When the driver receives a pulse signal, it drives the stepper motor to rotate a fixed angle in the set direction (known as the stepper angle) and rotate at a fixed angle. The angular displacement can be controlled by controlling the number of pulses to achiev...

Christian

2024-03-25

186

1

0

How many stepper motors can a 32 microcontroller control?

Gilbert

2024-03-23

252

2

0

Laser crystal carving technology is currently the most advanced and popular glass carving processing method internationally. It combines precision laser carving with transparent crystal materials to create lifelike three-dimensional images and textures, as well as impressive optical effects.The principle of crystal engraving is similar to that of...

Cyril

2024-03-23

250

1

0

1. Overtravel faultWhen the servo motor exceeds the soft limit set by the software or the hard limit set by the limit switch, an overtravel alarm will occur. Generally, the alarm content will be displayed on the CRT. According to the server maintenance manual, the fault can be eliminated and the alarm can be lifted.2. Overload faultWhen the load ...

Clarence

2024-03-23

238

1

0

1、 Selection of stepper motor torque. The holding torque of a stepper motor is similar to the power of a traditional motor. Of course, there are also essential differences. The physical structure of a stepper motor is completely different from that of an AC/DC motor, and the output power of the motor is variable. Usually, the type of motor is selec...

Smith

2024-03-22

204

2

0

The Failure Forms of Chain Transmission1. Fatigue failure of chains2. After a certain number of cycles, the chain plate will fracture due to fatigue3. The surface of the sleeve and roller will experience fatigue pitting due to impact4. The fatigue strength of the chain is the main factor determining the load-bearing capacity of the chain transmissi...

Williams

2024-03-22

218

2

0

A group of researchers from the Fraunhofer Institute of Applied Optics and Precision Engineering IOF and the University of New Mexico successfully cooled silica glass by 67 Kelvin for the first time using optical laser cooling. Researchers from Jena and Albuquerque have published their results in the journal Optics Letters.Cutting, drilling, weld...

Abel

2024-03-22

217

1

1

CNC equipment requires the use of servo motors because servo motors have characteristics such as high precision, high response, high speed, and high reliability, which can meet the requirements of high-precision control for CNC equipment. The servo system in CNC equipment generally consists of servo motors, encoders, controllers, etc. The servo mot...

Keegan

2024-03-21

203

2

0

1. More environmentally friendly: No need to use any chemical agents or cleaning liquids, the cleaned waste is basically solid powder, small in size, easy to store, recyclable, non photochemical reaction, and does not produce pollution.2. Good effect: Laser cleaning is non abrasive, non-contact, and has no thermal effect. It does not generate mec...

Tory

2024-03-21

211

1

0

When laser processing aluminum, multiple preventive measures should be taken to ensure safety and achieve optimal results. Here are some important preventive measures to consider:1. Laser safety: When working with lasers, laser safety should be of utmost importance. Ensure that the laser system complies with safety regulations and standards. Use a...

Marshall

2024-03-21

266

1

1

How to design the module of gear transmission? Before answering this question, the first thing to know is what gear is here - bevel gear, spur gear, or face gear. The design of different gears is different.Corresponding to different fields, the design criteria for gear transmission are also different. If it is a gear transmission in the field of ...

Roderick

2024-03-20

204

1

0

Viewpoint 1When the servo motor shakes at zero speed, it should be because the gain is set high, which can reduce the gain value. If there is a slight shaking during startup, the alarm will stop, and it is most likely due to incorrect motor phase sequence.Viewpoint 21. When the PID gain adjustment is too large, it is easy to cause motor vibration...

RTP

2024-03-20

225

1

0