Is the servo motor driving the outer gear to drive the inner gear to rotate and move as shown in the diagram, and is the precision of repeated positioning in multiple positions reliable during operation? For example, the module of the internal gear is 4 and the number of teeth is 220.

Roderick

2024-01-30

249

2

0

Stepper motors can achieve open-loop control of position and speed based on the number and frequency of pulses, making them an inexpensive, simple, and user-friendly control type of motor. They are increasingly widely used in the field of automation control. However, due to the fact that the stepper motor is not a closed-loop control, improper sele...

Silvano

2024-01-30

242

1

0

Firstly, when using this device, we must find the correct usage method and steps. Improper operation can cause the device to malfunction. Improper operation can directly affect work efficiency, slow down the production speed of the entire workshop, and also consume a lot of energy. Here are some suggestions for your reference:1. Please ensure tha...

Aaron

2024-01-30

228

1

1

ECI and PCI advantages1. ECI:1) No need to rely on industrial computers, which can reduce the configuration requirements of PCs and reduce the volume of industrial computers;2) No need to install PCI drivers, one network cable solves the problem;3) Regardless of the number of axes, all products call a set of API functions;4) No need for PCI adapte...

Cruise Wang

2024-01-29

301

2

0

1. Controller: used to generate trajectory points, i.e. expected output.2. Driver: Used to convert control signals (usually speed or torque signals) from motion controllers into higher power current or voltage signals, and output them to actuators.3. actuators: such as hydraulic pumps, cylinders, linear actuators, or motors, used to output motion.4...

Henry

2024-01-29

290

1

0

I have come into contact with many torque control machines and always think that torque control is more useful than torque clutch, with average accuracy; The servo accuracy is good, the response is fast, but it may not be applicable to all, and the price is high; Poor air pressure accuracy; Hydraulic complexity, difficult to control.

Jamie

2024-01-29

270

1

0

So I have a RDC6432G on my Omtech laser. I’m having problems getting my rotary to work.I have seen posts about when enabling rotary the commands are sent out the U axis. This does not seem to be the case with this controller, but if anyone knows how to change it to use U axis, that would actually help some.I have the Manfield ...

CXje56nO

2024-01-28

293

1

1

Hallo everyone!I hope you can help me, I’m slowly running out of ideas.I’ve upgraded my old 130w CO2 laser from a Puhan Ph3 controller to a new Ruida RDC6445Scontroller (complete set).Laser power supply, motor drivers, etc., remained the same.The conversion itself was not difficult.Now, everything seems to work fine.Home posit...

Pr0phezz

2024-01-27

294

1

0

Is there a wiring method for servo motors that requires constant accuracy while following the rotor and rotating. If using a slip ring to connect the motor line and encoder line, will there be any out of step phenomenon? Is there any other better connection method.

roy

2024-01-26

228

1

0

Two sets of pulses are respectively connected to the same servo. One set of pulses controls the forward rotation of the motor, while the other set controls the reverse rotation of the motor. The two sets of pulses will not be triggered simultaneously. There is a program for servo pulse segments behind. The device is an old device that should have b...

Liam

2024-01-26

259

1

0

My camera window takes up entire screen and I cant move, shrink, or close it. Any way to reset it?

Nugent

2024-01-25

285

2

0

I am running an Atomstack X20 Pro and I tried to install the rotary to do glasses. I have completly messed up the controller settings. My laser isn’t framing or firing and keeps bashing against the rails. Is there a factory reset on the machine? I need to start again as I have done something very wrong.

Vasili

2024-01-25

238

2

0

I just wasted this morning fighting with a non-existent laser problem!Somehow LightBurn “Start from” got changed from “Absolute coords” to “Current Position”. Since I always work in Absolute coordinates I did not even think to check this setting.Is there a way I can get LightBurn to always start in Absolute coord...

Payson

2024-01-25

251

1

1

Gas analysis is a key technology used to identify and control pollution in the optoelectronic production process, which can avoid equipment defects, economic losses, and reduce safety risks. This article explores the importance of pollution control in optoelectronic manufacturing, gas analysis techniques, applications, and the latest developments....

JOST

2024-01-24

236

1

0

On the main window I have my preferences to inches. The grid on side and top do not have a inch between them how do I change the grid where I can see every inch space hope this makes sense thanks Dennis.

Cruise Wang

2024-01-24

243

2

0