I get very bad curves. Belts are tight. What else happens? Is this normal from the stepper motors or something i have to check?Thanks in advance

Andrej

2024-11-18

213

2

0

I am sure I am not the only one here that has this happening, most likely with every K40 machine. My machine reaches max output milliamp output at 22-23% output in Lightburn. Would it be possible to calibrate the power output so that it reaches max Milliamp output at 100% in Lightburn power settings?

Hiroko

2024-11-12

291

4

0

Hi forum,I’m just strting with my JTech laser on a Onfininty Elite machine and was trying some different setting yesterday on oak.What I saw is that with a offset fill I have clean edges. But with just the lines, they are serrated.Any idea how to avoid this?

Carey

2024-11-09

264

6

0

My Gweike laser was working fine, it recently started saying I have the material thickness set to or near zero. I did not even know you can set the material thickness. Anyone know why this is showing up and how to fix it? 

AL.TAL

2024-11-15

229

1

0

Any of you out there consistently cut half-inch acrylic? I did it once by trial and error and because my settings were wrong, I actually damaged my edges a little bit. I only have one piece to get one shot at this.I have access to a shared machine, which is 100 W. We have a 4 inch cutting head In which I don’t have that much experience with.Can you...

さいと康成

2024-11-15

229

2

0

it doesnt matter what i try I can draw a circle and then a square and the weld command may or may not highlight… booleon never does. it just started in current version

Erdogan

2024-11-15

210

1

0

Vibration knife is a new type of CNC cutting equipment, whose principle is that the vibration knife blade vibrates up and down at a very high frequency, and through repeated cutting in a short period of time, it can quickly complete the machining. Under the command of the control system, the vibrating knife can complete designated tasks with high a...

Darren

2024-11-15

233

0

0

I have an Atomstack A70 with a movable z axis, the issue is that when I home the machine the z axis does not move up. I can move it with the move buttons and with a z home macro $HZ. The x and y axis home as they should. Thanks.

55455rml

2024-11-08

212

5

0

Just curious how the folks here have found using certain places on the X/Y table for placement of the work material ?I noticed, and makes sense, alot of folks use the back left corner to set up a square for dropping in material or maybe a work jig to engrave or cut.This makes sense as this is the best point for the mirror distant and it should fol...

Silvano

2024-11-11

177

3

0

I discovered after scanning some letters that the “insides” of some letters (think the “bowls” in capital B) were separate from the “outside” of the letters. I know I can Group the two objects (inside and outside) but the grouping can easily (for me) be undone accidentally. It appears that the only way of permanently joining them is to Weld them. H...

Narrator

2024-11-13

210

1

0

Hi all, I’ve been running Lightburn on an Ortur LM3 for about a month now, and a new issue has developed.I’m running a batch of bookmarks with this program, and it starts up fine, frames my object in workspace center, and runs the program in workspace center. But then…IF I PRESS START AGAIN: It repeats the program, but about 30mm to the left.IF I F...

berainlb

2024-11-13

217

1

0

Ruida 6432g will it allow a rotary hooked up to the u axis I have been trying to use the Y acess hooked to my 3 jaw rotary but it doesn't seem to let lightburn to change steps  can someone that really knows help me 

A679218C

2024-11-14

239

1

0

So I have a Creality Ender 3 S1 Plus with 5W laser module set up. It has not been cutting at its full power, because it cut the same material at the same speeds in Creality Print. So I found out that the S-Value Max setting needs to be set to your machine. My problem is I don’t know what setting to set it to. I’m including a picture of my machine s...

James

2024-11-12

250

1

0

Good morningi have a co2 laser with 6445g controlleri am engraving on granite. i have a problem with horizontally banded lines on engravingis there an upgrade of 6445g. if ibuy new like 6445gt will it be solved the problem?had anyone the same problem? please help!

029EE9D7

2024-11-11

264

1

1

Last night i was running my CO2 laser engraver and everything was running fine. Came out this morning powered on the engraver and the intial start up the head move just fine. Tried to relocate the head of the laser on the ruida controller and nothing moves.  I can't get the head to to move in either direction and the bed will not move. Light 14 is ...

36FC0F44

2024-11-11

232

3

0