Ελληνικά

Photon chips help drones fly unobstructed in weak signal areas

199
2023-10-28 09:58:39
Δείτε τη μετάφραση

With funding from the National Science Foundation of the United States, researchers at the University of Rochester are developing photonic chips that use quantum technology called "weak value amplification" to replace mechanical gyroscopes used in drones, enabling them to fly in areas where GPS signals are obstructed or unavailable.

Using this quantum technology, scientists aim to provide the same sensitivity level as large optical gyroscopes on small handheld photonic chips, which may alter the navigation of drones.

Jaime Cardenas, an associate professor at the Institute of Optics, has received a new National Science Foundation grant to develop this chip by 2026.

Cardenas stated that the fiber optic gyroscopes currently used on the most advanced drones include several kilometers of fiber optic spools or have limited dynamic range.

At present, the sensitivity and stability of gyroscopes must be fundamentally balanced between their size and weight. As unmanned aerial vehicles, drones, and satellites become smaller and more common, the demand for ultra compact navigation level gyroscopes will become crucial. The most advanced micro gyroscopes are compact and sturdy, but their performance is insufficient, which hinders their application in navigation.

According to Cardenas, weak amplification has more advantages than traditional methods because it can enhance the interference measurement signal without the cost of amplifying several forms of technical noise. But the previous weak amplification demonstration required complex laboratory settings and precise calibration; Cardenas is committed to achieving weak amplification on micro photonic chips using high-quality factor ring resonators.

Cardenas' collaborators in this project include physicist Andrew Jordan, who was a former faculty member at the University of Rochester and currently works at Chapman University. Cardenas stated that he will also collaborate with the David T. Kearns Leadership and Diversity Center at the university to expand the participation of underrepresented groups and stimulate their desire for STEM careers through research experience with high school students in the Rochester City school district.

Source: OFweek

Σχετικές προτάσεις
  • The Japanese research team has manufactured a vertical deep ultraviolet emitting semiconductor laser device based on AlGaN, which is expected to be applied in fields such as laser processing

    Recently, a Japanese research team has developed a vertical deep ultraviolet emitting semiconductor laser device based on AlGaN, which is expected to be applied in laser processing, biotechnology, and medical fields.As is well known, ultraviolet (UV) is an electromagnetic wave with a wavelength range of 100 to 380nm. These wavelengths can be divided into three regions: UV-A (315-380 nm), UV-B (280...

    2023-10-23
    Δείτε τη μετάφραση
  • Semiconductor lasers will support both TE and TM modes

    Typically, for lasers in optical communication systems, waveguide designs are used to achieve a single transverse mode. By adjusting the thickness of the surrounding area of the cladding layer and the etching depth of the ridge in the ridge waveguide device, a single mode device can be obtained. The importance of lasers is reflected in the following aspects:A chip without ridge waveguide design an...

    2023-10-20
    Δείτε τη μετάφραση
  • Developing nanocavities for enhancing nanoscale lasers and LEDs

    As humanity enters a new era of computing, new small tools are needed to enhance the interaction between photons and electrons, and integrate electrical and photon functions at the nanoscale. Researchers have created a novel III-V semiconductor nanocavity that can limit light below the so-called diffraction limit, which is an important step towards achieving this goal.In the journal Optical Materi...

    2024-01-29
    Δείτε τη μετάφραση
  • From Fiction to Reality: Laser Cutting Technology Has Entered the Shipbuilding Industry

    Laser cutting is a type of metal processing. In industry, there are three main cutting methods: mechanical cutting, thermal cutting, and a set of high-precision cutting methods. Laser technology belongs to the third category. The cutting in this method occurs due to the influence of the laser beam on the product. In fact, it is the molten metal produced by rapid pulse point melting and then blowin...

    2023-12-28
    Δείτε τη μετάφραση
  • Revealing the essence of optical vortices: a step towards understanding the interaction between light and matter

    In a groundbreaking scientific study published in Volume 13 of the Scientific Report, researchers reported on the results of Young's double slit interference experiment using oscillating vortex radiation under a photon counting system. The experiment involves using a spiral oscillator to emit second harmonic radiation in the ultraviolet range. Using an ultra narrow bandpass filter in the low curre...

    2023-12-29
    Δείτε τη μετάφραση