Perovskite solar cells are solar cells that use perovskite type organic metal halide semiconductors as absorbing materials. They belong to the third generation of solar cells and are also known as new concept solar cells.operational principlePerovskite solar cells are solar cells that use perovskite type organic metal halide semiconductors as abs...

Patrick

2023-11-28

406

1

0

Having an issue with slots. On a drawing with several slots, all 3mm, only a few actually appear to be editable.I’ve checked there are no extra nodes or rounded corners in the drawing. The drawing seems to be closed as I only see one green node. No errors are present in the dialog box.

Christian

2023-11-28

392

1

0

I was using the same speed and the same power, but then it slows down a lot, but i dont know the reason, what reason can it be?I was using my laser cut machine to cut the polywood in 3mm and with the suggested speed power and pass, but then the machine just no more able to cut it through as from the beginningfor my laser the suggested speed is 350,...

Nugent

2023-11-28

347

1

0

I intend to cut two lines to transform the two areas into one. When I do “trim line” the line n stays in one. Then it creates open part problems. Does anyone know a way to not have to see each zone to manually join these points that don’t stay together?

Vasili

2023-11-28

340

1

0

Although it may be used to cut a wide range of materials with accuracy and versatility, laser cutting has several risks that should be considered before using it regularly. Certain steps need to be taken to guarantee both safety and the best possible outcomes. General safety measures for maintaining laser cuttings include the following:1. Put on ...

Terrelle

2023-11-27

338

1

0

Buen día, ¿alguien podría ayudarme para corregir o saber porque pasa esto? Agradezco de antemano su atención

Clarence

2023-11-27

452

1

0

I would like to buy a new notebook. What are the minimum system requirements for LightBurn to work properly (storage space, graphics card, etc.).I will also work with CORELDraw Graphics Suite 2023. I think if I stick to these requirements, LightBurn should also work perfectly.

Gilbert

2023-11-27

361

1

0

Have tried the Lightburn material test with 2 different lasers but operated with the same laptop. When running the test pattern, the line speed will change but the fill speed seems to remain the same. Seeing very little if any change in the fill rates.Tried on a 2 year old Ortur Lm2 10w and a fairly new Xtool d1 pro 20w.1st was set at 20 to 100 % &...

Darren

2023-11-25

425

1

0

I am simply trying to turn my Atezr L2 24w machine on, set it up, and get going! Every time I turn it on, it immediately starts beeping saying a flame detected. I have tried rechecking everything over and over and am at a loss. I can’t get started on anything and very frustrated. The I seem to have everything setup correctly, have looked at h...

Miller

2023-11-25

370

1

0

I had to format by computer , i am now reinstalling all of softwares i need including LBthanks God i made a copy of my previous machine setting file and i dragged and dropped it in to working area and LB seems ok.i imported it twice by mistake and now i have also a undesired copy (3) of my own machine settingPoint is that by default any time i ope...

Smith

2023-11-25

422

1

0

I have a template file that I got online by someone else.This is similar to the LightBurn’s Test Material option, but a bit more in depth.This is apparently done with multi mode (sub layers), but I cannot figure where the settings are configured (increment of power).All CO2 (red) layer is 2400 speed, okay. But how to set the 10% increment in...

Marshall

2023-11-24

386

1

0

When I try to engrave a simple word, the job aborts and I get an error in the console about a line in the GRBL code needing to be an integer:I tried a new USB cable but it still happens.

Keegan

2023-11-24

380

1

0

Since two weeks I have a problem. I engrave tekst onto wood and since two weeks the background is also slightly burned. I use the laser and software for over a year now but this never happened before. restarting the program doesnt help. What is going wrong?

David

2023-11-23

411

1

0

OK, somehow a color has linked to a setting. When I open LB create a shape and use that color it comes up 'LINKED" would not be an issue but it is not a setting for that color I use. I can manually unlink it and set to the proper settings, but it is a pain. I’m lazy. Can not find where to permanently UNLINK the color. help…

Jamie

2023-11-23

363

1

0

Hello everyone, I wanted to engrave a dog tag for my dog, the material is matt stainless steel, which also worked well with the settings 450 speed and 100 power. in addition, I set the power on my Ray5 to 120. Now it’s just that the lower start is not engraved properly but remains rather light. what could be the reason for this? would it help...

Henry

2023-11-23

346

1

0