- Gelöst
How to solve the problem of uneven carving bottom in RDC8445S control system?
I used the RDC8445S control system for carving and found that the bottom of the carving was uneven. After careful inspection, I found that this problem occurred in different areas, especially in large...
- galvo scanner
- assist gas system
- beam delivery system
- RDC8445S
- RuiDa
- 1 Benutzer hat geantwortet
227 - Ungelöst
Why doesn't the Z-axis motor of RDC8445S controller move in manual mode?
Hello everyone! CO2 laser cutting machine with RDC8445S control system, switch to manual mode, and try to control the Z-axis motor through the Z+and Z - buttons on the operation panel. However, no mat...
- motion system
- coordinate axis
- RDC8445S
- CO₂ laser
- RuiDa
- 1 Benutzer hat geantwortet
276 - Gelöst
RDC8445S controller multi-point positioning function cannot be used
My cutting machine uses a ruida controller, RDC8445S， I set the U-axis as the rotation axis for cylindrical machining, but I found an issue: once the rotation axis mode is enabled, the normal multi-po...
- rotate
- coordinate axis
- RDC8445S
- control system
- RuiDa
- 2 Benutzer haben geantwortet
238 - Ungelöst
Ruida RDC8445S Controller Stuck on Boot Screen
My laser controller is a Ruida RDC 8445S. It stopped booting; the screen flashes and gets stuck on the loading arrow indefinitely. I also tried connecting it to the computer, but the controller never ...
- RDC8445S
- laser engraving
- laser marking
- laser cutting
- RuiDa
- 2 Benutzer haben geantwortet
275 - Gelöst
The RDC8445S controller is experiencing issues with the XY axis control not functioning
I have a CO2 laser cutting machine equipped with an RDC8445S controller. Today, while operating it, I suddenly noticed that the XY axis could not be controlled normally. Whether I operated it manually...
- coordinate axis
- RDC8445S
- CO₂ laser
- laser cutting
- RuiDa
- 2 Benutzer haben geantwortet
246 Troubleshooting Method for Slow X-Axis Reset in CO2 Laser Cutting and Engraving Control System
When using CO2 laser cutting and engraving control systems such as the RDC6612U or RDC8445S, if the X-axis reset speed is slow, follow these steps to systematically check for potential causes and make...
- coordinate axis
- RDC6612U
- RDC8445S
- CO₂ laser
- RuiDa
Caspar24902- Gelöst
Why can't the RDC8445S control system access the main interface?
Hello! When I opened the RDC8445S control system, the device started smoothly, but the control panel could not load the main interface properly. There is no cursor display on the screen, only a flicke...
- RDC8445S
- control system
- CO₂ laser
- RuiDa
- 2 Benutzer haben geantwortet
251 Solution for CO2 cutting and carving controller, computer unable to recognize USB driver
When using the CO2 laser cutting and engraving controller, if the computer cannot recognize the USB driver and displays that it cannot be installed, you can follow the following steps to troubleshoot ...
- USB
- RDC6612U
- RDC8445S
- CO₂ laser
- RuiDa
Michael24402- Gelöst
Using RDC8445S control system, cannot start from the positioning point set on the panel
I used the RDC8445S control system to carve workpieces today. I set a positioning point on the panel, but it did not start from that positioning point. What is the reason?
- RDC8445S
- laser engraving
- control system
- RuiDa
- 2 Benutzer haben geantwortet
288 - Gelöst
RDC8445S, x-axis reset speed is very slow
I have a CO2 laser cutting machine that uses the RDC8445S control system. When performing a reset to zero operation on the X-axis, its travel speed is abnormally slow, significantly lower than the sta...
- coordinate axis
- RDC8445S
- control system
- CO₂ laser
- RuiDa
- 3 Benutzer haben geantwortet
267 - Gelöst
After my RDC8445S control system started processing, the panel displayed a water protection alarm
seek help! It's frustrating! I turned on the machine today to prepare for cutting the workpiece. I turned on the control system and after starting the processing, the panel displayed a water protectio...
- RDC8445S
- control system
- cooling system
- CO₂ laser
- RuiDa
- 4 Benutzer haben geantwortet
271 - Ungelöst
RDC8445S mirrors images horizontally how can I correct this? Buttons on controller move axis in correct direction, image is not inverted on computer.
RDC8445S mirrors images horizontally how can I correct this? Buttons on controller move axis in correct direction, image is not inverted on computer.
- RDC8445S
- control system
- RuiDa
- 2 Benutzer haben geantwortet
274 - Gelöst
RDC8445S for co2 laser, reset button malfunction
My co2 cutting machine has been upgraded with the Ruida control system, model RDC8445S. When I press the reset button, there is no response. What could be causing this? Help!
- RDC8445S
- control system
- CO₂ laser
- laser cutting
- RuiDa
- 2 Benutzer haben geantwortet
304 Why do I need a microsd slot inside the RDC8445S?
Why do I need a microsd slot inside the RDC8445S? It is also unclear what is written on the board on the left under the sticker. "RDC6642G-core wifi-c v1.0"
- RDC8445S
- control system
- RuiDa
X-Shadow1.5K51Clarification on compatibility of ruida 8445s with rdv print
hope this email finds you well. I am writing to seek clarification regarding a point of discussion we had previously concerning the compatibility of RDV Print with the RD-8445S controller. You had men...
- RDC8445S
- control system
- RuiDa
8F4A188E93230
RDC8445S
32
Themen26
Follower
Warten auf Antworten
- RDworksV8可以加工锤子画吗？
- Where can I download the firmware upgrade file for the RDC6445 series controller?
- After installing the RDWorksV8 plugin in CorelDRAW, how can I do engraving and cutting at the same time?
- Edge tracing for contour cutting
- How do I adjust the time displayed on the C320？
- problema na cnc
- Mantisoft User guide or Manual
Copyright © 2021 Shenzhen Chanelink Network Technology Co., Ltd. All Rights Reserved.