For example, Mitsubishi FX20GM module, compared with PLC pulse output control has what advantages?
2023-03-2246010If you use m0 to drive the ddrvi command to cause the servo action to travel 10000 pulses, and if the command is not fully executed (6000 pulses have been driven), m0 is disconnected. When m0 continues to be connected, do you want to travel 4000 pulses or 10000 pulses?
2023-03-2156610Do you want to use an emergency stop to power off, to disable all outputs, or to use an emergency stop to pause in the program?
2023-03-2149210I have a set of B2 servo in my hand. I would like to ask how to use B2 to control the motor for some simple movements, such as controlling the screw module from point A to point B (taking 10 seconds).
2023-03-2056610Set the number of pulses per servo turn. When the lead screw stroke is 32mm, the servo setting is 3200 revolutions per turn, and the maximum output of the PLC is 100K. In this way, the maximum speed of the servo can only be 1850 revolutions. How can the maximum speed be 3000 revolutions?
2023-03-1764310The closed-loop controlled frequency converter can achieve closed-loop position control in the stopped state through encoder detection, locking the servo motor shaft at a fixed angle. This function is called servo motor locking or zero servo function.
2023-03-1847210One equipment on the production line and one servo are transplanted to the normal position. It has been determined that there is no problem with the mechanism. It should be an interference problem. The servo is Panasonic servo motor. I don't know how to eliminate this problem?
2023-03-1351210The can is broken, and the pressure is rhythmic. This is the hydraulic part.On the other hand, the servo motor follows the rhythm of the energy storage tank and goes off and on.Oil and electricity are irrelevant.
2023-03-1059410Please tell me how to deal with the servo hitting the limit during automatic operation?
2023-03-0840610Hi,I am about to finalize my order of CF-30 which has a “cloudray integrated control card” and also a “BJJCZ Control board”.The later, I assume to be working fine with Lightburn (with galvo license), correct?The CF-30 is delivered with a touchscreen control panel, which runs with a self-developed software by CloudRay. Can...
2023-03-0650410I have been trying to find out if there is a way to turn down the power supply to match my tube. I did a ramp test and my tube is rated to max out at 26ma but the controller is only at 70%. I want to make 26ma 100% so no one over drivers the tube. Is this possible?
2023-03-0650410The servo motor is used with the reducer, such as the planetary reducer. The reducer has a reduction ratio. The servo motor outputs the specified speed. After the reducer decelerates and increases the torque, will the speed accuracy of the output shaft of the reducer be improved? Or does the reducer affect the speed accuracy of the servo motor? Is ...
2023-03-0461310The reason why the motion control card cannot be connected
2023-03-0465010The response speed is a very important index to measure the motion control system. In addition to the response speed, there are also some important parameters related to product quality and production efficiency:1. The number of axes supported by the controller and the performance of multi-axis linkage and cooperation.2. Accuracy of...
2023-03-0452000Panasonic MSMF series servo motors, 50W and 100W are all suitable for the same type of drive. The original 50W motor is used, but now the 100W motor is replaced. Is its current, torque and other parameters adaptive? Does the torque monitor output signal including IM terminal correctly reflect the motor torque after replacement?
2023-03-0250910
- Keine Daten
Deutsch
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski