Servo motors are widely used in the field of automation control, such as in robotic arms and AGV vehicles, where there are varying numbers of servo systems. So, what are the future development trends of servos? Let's put it simply.1. Communicationalization.There are more and more servo motors of communication type. Compared to DC servo motors, AC...

jessie

2024-03-15

474

1

0

Laser chiller equipment is one of the common equipment in our production field, and cooling water is used to cool the chiller equipment. Someone asked, can the cooling water of the laser chiller use well water or river water? NO!. For laser chillers, under normal circumstances, we usually use pure water to add. Next, let me analyze for you, what ar...

roy

2024-03-15

423

1

0

The abnormal noise of servo motors can be caused by various reasons, and the following are some common reasons:Bearing wear: Bearings in servo motors may wear out due to prolonged or improper use, resulting in abnormal noises. When bearings wear out, metal friction sound and noise will be generated, and bearings need to be replaced to solve the p...

Terrelle

2024-03-14

496

1

0

As is well known, refrigerant is used in refrigeration systems to transfer heat energy and produce refrigeration effects. It is an intermediate substance in the refrigeration process. It first receives the cooling amount of refrigerant to cool down, and then cools other cooled substances. The refrigerant used in air conditioning is well-known. In f...

Payson

2024-03-14

429

1

0

Laser cutting, as one of the most popular material processing methods at present, has a wide range of application fields, and has been fully used in many industries such as automobile manufacturing, hardware processing, tableware and kitchenware, clothing and leather, advertising decoration, aerospace, etc.For new operators, it is not difficult to ...

Vasili

2024-03-14

459

1

0

With the development of industrial technology and the increasing maturity of laser processing technology, the use of lasers has a very large market share in industrial manufacturers. At present, the most commonly used cooling system for laser equipment such as laser marking, laser cutting, laser cleaning, laser engraving, laser welding, and laser c...

Miller

2024-03-13

430

1

0

Manual control: Actually, it's just some simple switch quantity control. The movement of servo motors is mainly controlled through manual devices such as physical buttons, switches, or joysticks. The advantage of this method is that it is relatively easy to operate and is commonly used in the debugging process of some motors.Signal input control:...

Darren

2024-03-13

534

1

0

A worm gear reducer is a reduction transmission device consisting of a worm gear and a worm gear. A worm gear is a helical gear, while a worm gear is a cylindrical body with helical teeth. Worm gear transmission is used for two shafts intersecting at 90 degrees. In worm gear transmission, the active part is the worm gear and the passive part is the...

Cyril

2024-03-13

455

1

0

After installation, the graphics card fan will turn on, but there is no sound of starting. What's going on?

Marshall

2024-03-12

450

3

0

Defects in copper alloy laser welding1. Welding stressThe coefficient of linear expansion and shrinkage of copper are also relatively large. The coefficient of linear expansion of copper is 15% higher than that of iron, and the shrinkage rate is more than twice that of iron. In addition, copper and copper alloys have strong thermal conductivity, wh...

Kevin

2024-03-12

510

1

0

The material selection of general mechanical transmission systems is a broad concept. Here, I will mainly talk about the situation of gear transmission in iron-based friction pairs, which is the selection of gear materials.Gears can be made of various materials, including steel, copper, cast iron, aluminum, plastic, and so on. Among them, steel i...

Aaron

2024-03-12

514

1

0

Hi there I am new to laser welding We weld aluminum with 2mm thickness The protective lens burnt so fast i change it 3 to 4 time a dayUsing 2000W fiber laser welding machine from depang model number dph-2000So any help to solve the problem

2Tqzijai

2024-03-10

501

5

0

When using a servo (Panasonic) to return to the origin in a recent project, if other axes are also moving, the Z-phase zero point signal received by the PLC is easily lost, resulting in abnormal return to the origin position. Later, upon checking the driver manual, it was discovered that the GND of the Z-phase zero point signal needed to be connect...

Henry

2024-03-11

527

2

0

As an indispensable supporting equipment for most lasers, laser chillers are responsible for cooling and cooling the laser. Matching a suitable laser chiller can provide good cooling effect for the laser and ensure its efficient operation. When the laser chiller works for a long time, the cooling effect decreases and the water temperature is not co...

Jamie

2024-03-11

467

1

0

1. Gear operation generates heata. Overload or ultra high speed.The driving load is too large, causing an increase in gear meshing sliding heat generation.b. Insufficient or incorrect selection of lubricating oil/grease.Too little lubricating oil/grease can cause oil film failure and increase meshing friction. In addition, improper use of lubricant...

David

2024-03-11

471

1

0