Fault analysis:1. The installation path is not selected correctly2. No VBA plugin downloaded3. The VBA plugin version is incorrect compared to the CAD version Solution:The reinstallation path is correct. After checking, it was found that the CAD version sent was 2023 and the VBA plugin version was 2018, which caused the failure. After re downlo...
05-1930300Frequency converters are widely used in modern industry, but sometimes there are occasional trips that cause inconvenience to production. Below, we will analyze the common causes of frequency converter tripping and provide corresponding solutions.Overload causes trippingOverload is one of the common causes of frequency converter tripping. When th...
01-1498411Fault analysis:1. No fan enabled2. Relay wiring is incorrect3. Layer setting issue Solution:The layer parameters are set to not blow air
05-1927700Fault analysis:1. Layer output setting error2. The laser power setting is too small3. Wrong selection of the number of interchangeable heads Solution:Despite increasing the power, there is still no light, and the cutting action is normalUpon inspection, it was found that the number of interchangeable heads was set to 2, but in reality, there wa...
05-1929800Fault analysis:1. Enable multiple positioning points2. Failed to locate successfully3. Panel button malfunction4. Return setting error Solution:Upon checking the user parameters, it was found that the return method has been changed to return to the mechanical origin. Simply change the return to the positioning point
05-1927700Fault analysis:1. Abnormal reset parameters2. Panel reset button malfunction3. Unstable and undervoltage power supply voltage4. Program firmware malfunction Solution:Firstly, check whether the reset parameters are normal, whether the user parameter reset is turned on, whether the motherboard wiring is under voltage, and confirm that the output ...
05-1927800HelloDoes anyone knows, will LightBurn works with Ruida RDC8445S ?I try trial version, and Ruida always in disconnected state, Serial USB/Ethernet IP both not works.PS: RDWorks detect controller by USB and IP (WiFi) - both success
05-1534010GZTECH QCW products, single-mode and multi-mode optional, suitable for precision welding and cutting applications of metals/ceramics and other materialsPower:75W 150W 300W 450W 600WOverviewGZTECH QCW lasers support simultaneous operation in both continuous and high peak power pulsed modes and can handle processing tasks that previously required ...
05-1535001GZTECH GT series MOPA Laser Source adopts the MOPA scheme of main oscillation power amplification, focusing on optimizing the pulse peak power and beam quality, and can maintain high beam quality under high-power working conditions, and its maximum peak power can be more than 150kW. GT MOPA Laser Source has the characteristics of small pulse width,...
05-1535501After working through a dozen issues, i thought i was ready to do a project. When I started the job, the laser went through the design but there was just a dot of light, no laser. I’m sure it has too be a setting?
2023-07-0449340Main features：Feedback protection 1020nm-1200nmOptical fiber numerical aperture 0.22 NAFiber core diameter 135μmOutput power 260WWavelength 976±1nmApplication：Fiber laser pump sourceScientific ResearchInstructions for use◆ Avoid eye and skin exposure to direct radiation during operation.◆ ESD precautions must be taken during storage, transpor...
05-1338101The 75W infrared picosecond laser is an industrial-grade ultrafast laser that uses a fiber seed source combined with solid-state amplification technology. It adopts an all-in-one machine design, the main body is completely sealed in a closed cavity, and there are multiple sensor monitors inside, which ensures the stability and reliability of the la...
05-1328600BWT Thunder series fiber lasers have good beam quality, which makes them perfect choices for precision processing. The two operation modes, CW and modulation, minimize heat-affected zone. Reliable performance, modular and all-fiber design, and robust case enclosing all optical and electronic components ensure that they can be used under strict indu...
05-1029600Hello!I am trying to figure out how to cut out a shape, in a piece of Material that is “precut”I have created this picture to explain what , and why I am trying to do it.I cant think of a way to do this, or even describe it, so if anyone has a suggestion, it would be appreciated.Referencing the picture!1. I have a piece of acrylic that is the ...
04-3063320I downloaded RDWorks V8, but every time I need to run it, it asks for the administrator. Is there a way to prevent this from happening?
05-0142910
- Keine Daten
Deutsch
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski