As one of the essential equipment of laser, the importance of laser water cooler is self-evident. In laser welding technology, laser is the core component of laser welding technology, it will produce a lot of heat in the work, its working state and performance are directly related to the refrigeration and effect of laser welding. In order to mainta...

jessie

2023-07-19

1.4K

1

0

When l trace image of hand writen drawing it creats lines either side of that line. How do l create centre line only Thanks

Williams

2023-07-18

1.1K

1

0

Is there a way to center an object to the middle of the frame. As you can see in the screenshots the object is off centered. Which means the object will be off centered on the coaster and therefore I can’t sell it and wasted time and a coaster.

Smith

2023-07-18

1.2K

1

0

1, failure mode: tooth brokenPerformance: The whole or part of the tooth is separated from the gear fracture or falls off, usually the root of the tooth is broken.Impact: Tooth fracture is the most serious failure form. Broken teeth often cause instantaneous transmission stuck or damage to the gearbox under the action of centrifugal force, result...

Miller

2023-07-18

1.4K

1

1

The piece did not move, but the top part of my design shifted?

John Trant

2023-07-17

1.3K

1

0

how can I create a .LBART file. I would like to create my own

Robert Evans

2023-07-17

1.2K

1

0

I have been using my 50w OMTech laser for about 3 years now. Recently, I’ve had a problem with my laser power, it just got very weak. It wasn’t gradual either, it just happened out of nowhere. I can’t cut 1/8th inch plywood anymore without doing like 10 passes now. I’ve tried increasing power, slowing my speed, it just won&r...

Henry

2023-07-17

1.2K

1

0

Laser chiller is mainly composed of compressor, condenser, capillary, evaporator four main components and some other components, before we introduced the harm of the condenser water temperature is too low, today and you briefly talk about the impact of the water temperature is too high on the laser chiller and the reason for the chiller condenser t...

Jamie

2023-07-17

1.4K

1

0

In the rapid development of laser technology in the society, the application of refrigeration equipment is more and more widely, in industrial production, especially laser equipment, most of the cooling are cooled by laser chiller, but in the process of using laser chiller will inevitably encounter this or that problem, if the laser chiller in the ...

David

2023-07-17

1.5K

1

0

Hello!im waiting now for my ikier laser max version.So is there a way to make different Cut/engrave profiles for switching 48w to 24w in Lightburn?Thanks in advance

Gilbert

2023-07-14

1.3K

1

0

Would any of y’all help me out my machine stops mid run on the the screen stills shows it as actively working but then when I stop and try to regime it does not move. Any help would be greatly appreciated

Payson

2023-07-14

1.1K

1

0

Good morningHave installed 3 styles of a font as TTF format under macOS (OTF doesn’t work at all).Now when I want to select a specific style, Lightburn only offers the standard selection with bold/italic and so on…but the font list doesn’t show the styles for my font, which are:regularalternatedoodleWill there be in near futur...

Vasili

2023-07-14

1.4K

1

0

Foxalien 4040xe, 80 w laser. Dell, windows 10. Laser was working fine. Yesterday i went to make a cut. It homed on startup, framed the work, then darted off to upper right corner on start. I have had this happen before, finally got it to work after deciding I had to use the set origin, not realizing that was the same as zeroing (Right?). I tried al...

Clarence

2023-07-14

985

0

0

Spectra Precision today introduced the Spectra Precision® GL1425C-class laser, a new dual-stage laser that joins a full line of specialty laser products.The GL1425C two-stage laser is a rugged, cost-effective and accurate laser that performs three tasks: leveling, grading and vertical alignment. Even in harsh work site conditions, the G...

David

2023-07-13

1.2K

1

0

I am cutting an outline design using the blue cut setting but need the lines to be a bit thicker. Is there any way to get thicker lines when using the blue setting. have tried bring in the design from Corel Draw with thicker lines but they still cut the same.

Tory

2023-07-13

1.3K

1

0