Hello. I recently upgraded Lightburn to 1.7.03. I am using Xtool Pro for my work. I am struggling to figure out why the laser head goes off in the wrong direction and then stops with a beep. It’s not hitting the limiter switch.Attempting to engrave an image on acrylic. Lining up the laser on the top left corner of the work piece and it frames the ...

Cruise Wang

2024-11-19

290

3

0

I have the same problem like in this video my machine add random extra line to my output cuttingany help ? https://www.youtube.com/watch?v=5DDVqcbVISM

SMIX24

2024-11-19

290

5

0

I gave up last year on trying to figure out my Boss Laser (LS1416) and just stopped using it, however last week I decided to take one more run at it. I now have a new issue stopping me. When I plug in my PiBurn rotary tool and try to do anything, the laser head slams into the right rail and starts grinding. I believe I am running a recent version o...

Ethan

2024-11-20

270

1

0

I get very bad curves. Belts are tight. What else happens? Is this normal from the stepper motors or something i have to check?Thanks in advance

Andrej

2024-11-18

253

2

0

I am sure I am not the only one here that has this happening, most likely with every K40 machine. My machine reaches max output milliamp output at 22-23% output in Lightburn. Would it be possible to calibrate the power output so that it reaches max Milliamp output at 100% in Lightburn power settings?

Hiroko

2024-11-12

335

4

0

Hi forum,I’m just strting with my JTech laser on a Onfininty Elite machine and was trying some different setting yesterday on oak.What I saw is that with a offset fill I have clean edges. But with just the lines, they are serrated.Any idea how to avoid this?

Carey

2024-11-09

304

6

0

My Gweike laser was working fine, it recently started saying I have the material thickness set to or near zero. I did not even know you can set the material thickness. Anyone know why this is showing up and how to fix it? 

AL.TAL

2024-11-15

257

1

0

Any of you out there consistently cut half-inch acrylic? I did it once by trial and error and because my settings were wrong, I actually damaged my edges a little bit. I only have one piece to get one shot at this.I have access to a shared machine, which is 100 W. We have a 4 inch cutting head In which I don’t have that much experience with.Can you...

さいと康成

2024-11-15

263

2

0

it doesnt matter what i try I can draw a circle and then a square and the weld command may or may not highlight… booleon never does. it just started in current version

Erdogan

2024-11-15

243

1

0

Vibration knife is a new type of CNC cutting equipment, whose principle is that the vibration knife blade vibrates up and down at a very high frequency, and through repeated cutting in a short period of time, it can quickly complete the machining. Under the command of the control system, the vibrating knife can complete designated tasks with high a...

Darren

2024-11-15

261

0

0

I have an Atomstack A70 with a movable z axis, the issue is that when I home the machine the z axis does not move up. I can move it with the move buttons and with a z home macro $HZ. The x and y axis home as they should. Thanks.

55455rml

2024-11-08

241

5

0

Just curious how the folks here have found using certain places on the X/Y table for placement of the work material ?I noticed, and makes sense, alot of folks use the back left corner to set up a square for dropping in material or maybe a work jig to engrave or cut.This makes sense as this is the best point for the mirror distant and it should fol...

Silvano

2024-11-11

218

3

0

I discovered after scanning some letters that the “insides” of some letters (think the “bowls” in capital B) were separate from the “outside” of the letters. I know I can Group the two objects (inside and outside) but the grouping can easily (for me) be undone accidentally. It appears that the only way of permanently joining them is to Weld them. H...

Narrator

2024-11-13

248

1

0

Hi all, I’ve been running Lightburn on an Ortur LM3 for about a month now, and a new issue has developed.I’m running a batch of bookmarks with this program, and it starts up fine, frames my object in workspace center, and runs the program in workspace center. But then…IF I PRESS START AGAIN: It repeats the program, but about 30mm to the left.IF I F...

berainlb

2024-11-13

250

1

0

Ruida 6432g will it allow a rotary hooked up to the u axis I have been trying to use the Y acess hooked to my 3 jaw rotary but it doesn't seem to let lightburn to change steps  can someone that really knows help me 

A679218C

2024-11-14

266

1

0