Türkçe

Changchun Institute of Optics and Fine Mechanics has developed a high brightness HiBBEE non-uniform waveguide semiconductor laser

749
2025-03-18 14:14:23
Çeviriyi gör

High brightness semiconductor lasers have extremely important applications in fields such as laser radar. Traditional semiconductor lasers face challenges such as large vertical divergence angle, elliptical beam output, multiple lateral modes, and poor beam quality, which limit the direct application of high brightness semiconductor lasers.

In response to this challenge, the team from the Bimberg Sino German Green Photonics Research Center at Changchun Institute of Optics and Fine Mechanics has adopted a high brightness vertical wide area edge emission (HiBBEE) structure in the vertical direction, using the photonic bandgap effect to replace the traditional total reflection principle for light field limitation, improving the size of the optical mode, and reducing the vertical divergence angle of semiconductor lasers; At the same time, in the lateral direction, non-uniform waveguides were used to suppress lateral higher-order modes, improve the lateral beam quality of semiconductor lasers, and optimize the design and preparation of HiBBEE non-uniform waveguide semiconductor lasers. At a current of 1.5A, the full width at half maximum of the vertical and lateral divergence angles is still as low as 8.6 ° and 5.1 °, while maintaining the fundamental mode output. The brightness is improved by 1.5 times compared to similar devices.

 


Schematic diagram of HiBBEE non-uniform waveguide semiconductor laser structure

 


HiBBEE non-uniform waveguide semiconductor laser brightness


This high brightness HiBBEE non-uniform waveguide semiconductor laser can significantly reduce the application cost of semiconductor lasers and has broad application prospects.

The first author of the article is Wu Chengkun, a doctoral student at the Sino German Center, and the corresponding author is researcher Tian Sicong. The research was supported by the Sino German International Cooperation Project of the National Natural Science Foundation of China (Research on 1250nm High Brightness Quantum Dot Laser for Lidar, No. 62061136010).

Source: opticsky

İlgili öneriler
  • The Trends and Challenges of the Metal 3D Printing Industry in 2025

    In the past decade, metal 3D printing technology has experienced rapid development, from the initial production of orthopedic implants to the manufacturing of rocket boosters. This technology has become an indispensable part of multiple key industries. With the advancement of technology and the expansion of the market, we are witnessing the revival of electron beam melting (EBM) technology and the...

    01-21
    Çeviriyi gör
  • In situ bubble point measurement using spectroscopy

    Develop and research a new downhole bubble point pressure measurement technology suitable for black oil and volatile oil to enhance well analysis using spectroscopy.Representative fluid characteristics are required for a wide range of oilfield lifespans, such as the initial scale and production planning of reservoir hydrocarbon reserves. Fluid characteristics are usually obtained from laboratory s...

    2024-01-31
    Çeviriyi gör
  • Amada launches latest precision laser welding workstation wl-300a

    Recently, Amada weld tech Inc., a Japanese supplier of welding and cutting solutions, grandly launched a new wl-300a precision laser welding workstation, which is equipped with advanced continuous wave (CW) or quasi continuous wave (QCW) fiber lasers. It has a wide range of applications, especially for metal welding and processing of selected plastic materials, especially in the aerospace field.Wl...

    2024-05-31
    Çeviriyi gör
  • Chuangxin Laser Industry Dedicated Laser and Solutions Help Promote the Intelligent Development of Cladding Application Industry

    Laser cladding technology, also known as laser additive manufacturing technology, uses high-energy laser as the heat source and metal alloy powder as the cladding material. Through the synchronous action of laser and alloy powder on the metal surface, it quickly melts to form a molten pool, and rapidly solidifies to form a dense, uniform, and controllable thickness metallurgical bonding layer, the...

    2023-11-01
    Çeviriyi gör
  • DataLase launches a new laser active transparent to white coating

    Laser coding and marking technology expert DataLase has launched a series of new colorless to white coatings for a range of packaging applications.These coatings are centered around biodegradable and sustainably sourced raw materials, providing high contrast white printing even on difficult substrates such as 12 micron PET and shrink film, under the weight of flexographic and gravure coatings. Thi...

    2024-03-09
    Çeviriyi gör