Polski

An efficient femtosecond pulse amplification technique for extracting the maximum stored energy in fiber laser amplifiers

504
2024-11-13 11:55:15
Zobacz tłumaczenie

The well-known journal Optica published a paper in November 2024 titled "Near complete extraction of maximum stored energy from large core fibers using coherent pulse stacking amplification of femtosecond pulses"The authors of the paper were the University of Michigan, Lawrence Berkeley National Laboratory, Peking University, and the German Institute of Synchrotron Radiation.

The specific technique is to use a cascaded "GTI" (Gire Tounois interferometer) method to synthesize 81 amplified pulses together in the time domain. The technical difficulty that needs to be overcome is to control the phase and amplitude of each pulse to achieve coherent synthesis. The core femtosecond light source is a 1 GHz repetition rate femtosecond fiber laser, developed by Professor Zhang Zhigang's group at the School of Electronics, Peking University.

The author of the paper has demonstrated using the aforementioned techniques that, with a continuous pump of 100 W and a repetition rate of 2 kHz, nearly 10 mJ of amplified pulse energy can be extracted, far exceeding the energy output of conventional large mode area fiber amplifiers, which can reach less than 1 mJ. The extraction efficiency is close to 90%.

This efficient time-domain pulse synthesis technique can greatly improve the efficiency of pulse synthesis and reduce the number of amplifiers used for spatial synthesis.

Although the repetition rate and pulse energy obtained from this experiment are not yet high, this technology demonstrates the potential to generate femtosecond strong laser pulses with Joule level pulse energy and repetition rates above 10 kHz. It may provide a light source for studying strong field physics and particle accelerators under extreme conditions, as well as for generating secondary radiation.

Figure 1 shows the efficiency of pulse energy extraction in a fiber amplifier independent of core diameter under nonlinear confinement. Figure 1 indicates that the pulse extraction efficiency can only approach 100% of the amplifier's stored energy when the pulse is broadened to 100 ns


Figure 2 shows a schematic diagram of a composite GTI cavity, where 81 incident laser pulses are coherently superimposed in four large loop cavities to form 9 pulses; Then coherently superimpose them into one pulse in four small cavities


Figure 3: Photo of the Composite GTI Chamber Experimental Device


Figure 4 shows the pulse waveform and spectrum of the coherent synthesized pulse with an energy of 3 mJ and a width of 313 fs

Source: Yangtze River Delta Laser Alliance

Powiązane rekomendacje
  • New Progress: III-V Laser and Silicon Optics Technology Achieve Single Chip High Integration

    Recently, Scientific Photonics, a supplier of silicon photonic integrated circuits (PICs) headquartered in Grenoble, announced that it has successfully integrated III-V-DFB lasers and amplifiers with standard silicon photonic technology into the production process of Tower Semiconductor.By utilizing proprietary technology and standard silicon photonics, Scientific Photonics has achieved full inte...

    2024-03-01
    Zobacz tłumaczenie
  • The world's first scalable optical quantum computer prototype has been launched

    Canada's Xanadu Quantum Technologies has developed the world's first scalable optical quantum computer prototype. The company published an article in the latest issue of Nature detailing its design and construction process, and demonstrating how the prototype can be flexibly scaled up to the required scale. This breakthrough lays an important foundation for the development of large-scale quantum c...

    02-12
    Zobacz tłumaczenie
  • Researchers have discovered a new method to improve the resolution of laser processing

    Customized laser beams focused through transparent glass can generate a small dot inside the material. Researchers from Northeastern University have reported a method of using this small spot to improve laser material processing and increase processing resolution.Their research results are published in the journal Optics Letters.Laser processing, like drilling and cutting, is crucial in industrie...

    2024-03-28
    Zobacz tłumaczenie
  • 43 seconds! Completion of laser welding of a new energy vehicle body

    March 8, in the three sessions of the 14th National People's Congress, the second “representative channel” focused on interviews, the National People's Congress, the party secretary of HGTECH Science and Technology, Chairman of the Board of Directors Ma Xinqiang, said in response to a reporter's question, in order to crack the “strangle  “technical problems, HGTECH over the years in the field of h...

    03-11
    Zobacz tłumaczenie
  • XTool enables pre-sale of F1 superfiber and diode laser cutting machines

    Tool has started pre-sales for the F1 Ultra, a 20 watt fiber and diode dual laser engraving machine. OEMs have stated that it is a win-win product and its so-called "flagship" model.Fiber lasers are mainly used for metal materials and usually work faster than diode lasers, but other materials have better performance when using diode lasers. F1 Ultra aims to bridge this gap by using a power of 20W ...

    2024-05-09
    Zobacz tłumaczenie