Panasonic MSMF series servo motors, 50W and 100W are all suitable for the same type of drive. The original 50W motor is used, but now the 100W motor is replaced. Is its current, torque and other parameters adaptive? Does the torque monitor output signal including IM terminal correctly reflect the motor torque after replacement?

Gilbert

2023-03-02

977

1

0

Ciao a tutti,Su una macchina morbidelli/scm ho un motore dedicato per fresature orizzontali. Il motore è verticale ma la fresa è rinviata tramite ruota dentata.Sul manuale della macchina non fa menzione di interventi periodici di lubrificazione del meccanismo, eppure sul corpo del rinvio c’è un tappo per l’olio.Sono...

Vasili

2023-03-02

854

1

0

I have recently changed the size of my Ortur LM2 Pro from the stock size to 80mm in the Y direction. I have changed the sizes within Lightburn to reflect the change. After drawing a 400mm x 800mm rectangle within the software, lightburn informs me I am out of the working area every time I try to frame the box. I checked to make sure I was within bo...

Patrick

2023-03-02

1.1K

1

0

How to select a suitable linear motor module to maintain the stability and efficiency of the equipment.Linear motor selection elements:1. The movement load, the maximum load that can be borne (the safety margin is 80%), and the movement center of gravity deviation.2. Linear motor installation mode: horizontal installation is the best way under the...

Clarence

2023-03-02

985

0

0

How do I change the settings in Lightburn so it knows the laser is now twice as powerful

Clarence

2023-03-01

1.2K

1

0

Hello I made a circle and drew a line through it and I tried to edit nodes using “t”. It didn’t do anything. Also, it doesn’t seem to allow me to add nodes to circle shapes.

Robert Evans

2023-03-01

1.3K

1

0

Why do I have to flip everything Vertical to get it correct on the surface I am engraving?

Williams

2023-03-01

1.3K

2

0

I am looking for help with my Ruida 6445G Controller. The problem is the Z Axis. I have tried multiple options. Trying to get the Z Axis to show me in mm the actual length is not happening. For 100mm on the Controller is only about 4mm movement. I tried using the Auto calculations of Entering this information and the stepper was set at 0.2 which th...

DJPeterLewis

2023-01-30

1.2K

11

2

I noticed that the new version of the software has added the option “Camera is mounted to the laser head”. Regarding this feature, I would like to know the following:1. What specific tasks can this feature help me with?2. What kind of camera do I need to prepare?3. What is the specific usage method of this feature? It would be great if...

Gilbert

2023-02-28

1K

1

0

I have Ortur LM2 Machine. I recently replaced the LU 1-4 module with a Comgrow 20w module. The new module is 63mm square and the LU 1-4 is about 40x42mm. I glued a protrusion on to the side of the new module to hit the x-axis homing switch and it works fine. I relocated the y-axis homing switch to the front rail of the Ortur. It works fine if the m...

Patrick

2023-02-28

1.3K

1

0

Why can't the temperature of water-cooled chiller drop? What are the reasons?Who can give me an answer?

roy

2023-02-28

896

4

0

I have a Nova 24 machine and use lightburn. I have looking over other discussions and this and have tried everything that people have indicated. Any other thoughts on this issue?

Liam

2023-02-28

914

1

0

High-performance commercial laser color printer, due to its high definition and special color, has high requirements for paper, and is used for drum driver. It is necessary to further reduce the speed fluctuation and prolong the service life. Therefore, the transmission device is driven by precision planetary reducer, which has high service life an...

jessie

2023-02-28

893

0

0

Hello I'm designing a CNC diode laser machine that can cut 16-Gauge stainless steel to earn my bachelor's at the university.Since Im new to this enviroment I would like to know how to calculate the power needed to cut that deep, I've searching this forum for answers but all I can find is people estimating 150-500W and not the actual formulas or par...

Henry

2023-02-27

1.2K

4

0

Laser week, we developed a new postprocessor for plasma bevel cutting machine, the control START Sharpon is used on it.Thanks for the new tool management feature involved in CutLeader V6, we could add severial tools with different bevel angle and the enty/exit radius.Based on the tool assignment rules, the bevel tool can be assigned to contour auto...

Jamie

2023-02-27

865

2

0