Nederlands

SEMA 2023: Huali's Easy Level Floating Free Laser Fuel Level Transmitter

202
2023-11-03 14:51:33
Bekijk vertaling

Winning the SEMA Best Engineering New Product Award is not an easy task. Therefore, it said a lot about Huali's new non floating fuel transmitter bringing hardware home. The Easy Level fuel level sender is a brand new design that does not rely on traditional float arm settings, but uses a frikken laser beam to measure the fuel level in the tank.

More precisely, Easy Level uses LiDAR technology to measure the distance between the fuel surface and the sensor unit, and then converts this distance measurement value into a signal that can be read by the fuel level gauge. It can be used with any aftermarket instrument, "said Steve Sparkman of Holley. It is not suitable for OEM instruments, but all aftermarket instruments - Classic Instruments, Dakota Digital, etc. - can be easily connected.

This sensor is suitable for tanks with depths ranging from 4 inches to 39 inches and can be set up outside the vehicle. By using the buttons on the device, you can set the empty and full positions before installation, and then set the same position on the instrument panel after installation. You can even adjust the damping rate of the reading through the DIP switch on the device to manage instrument bounce caused by fuel shaking.

This device is very compact and easy to install. It looks like a hockey ball, "Sparkman said. It has a laser that can shoot down and tell you where the fuel is. It's so simple. Installation is a simple task, including installing hardware and gaskets, as well as installing flange templates. The small bolt circle diameter of 2-1/8 inches hardly occupies space on the fuel tank, and the 12 volt PWM output signal makes sensor wiring easy.

Source: Laser Network

Gerelateerde aanbevelingen
  • New progress in in-situ identification and quantitative research of methane carbon isotopes in the ocean

    Recently, Zhang Xin's research team from the Institute of Oceanography, Chinese Academy of Sciences, based on the in-situ laser Raman spectroscopy technology, made new progress in the in-situ recognition and quantification of methane carbon isotopes by using the significant differences in the Raman spectra of methane carbon isotopes (13CH4 and 12CH4). The relevant results were recently published i...

    2023-10-13
    Bekijk vertaling
  • Tsinghua University makes progress in the field of pre sensing optical computing

    In the era of the Internet of Things, visual image sensors, as key devices in the intelligent society, are embedded in various devices such as mobile communication terminals, smart wearable devices, automobiles, and industrial machines. With the continuous expansion of applications, higher requirements have been put forward for the system power consumption, response speed, safety performance, and ...

    2024-08-05
    Bekijk vertaling
  • Mei Xin Sheng: The development of high-precision polarized light crown products has been completed

    On September 5, when Mei Xin Sheng held an analyst meeting, it said that the company has launched a fully integrated ultra-low power optical proximity detection sensor and a three-in-one ambient light and proximity detection sensor with ultra-high sensitivity, which have entered mass production.The research and development of high-precision polarized light crown products has been completed, the fe...

    2023-09-05
    Bekijk vertaling
  • Fundamentals of Next Generation Photonic Semiconductors: Small Lasers

    This week, an illustration was published on the cover of the international journal Science, showcasing a powerful mode-locked laser emitted from a miniature photonic semiconductor.A research team led by Alireza Marandi, a professor of electrical engineering and applied physics at the California Institute of Technology, has successfully developed a conventional mode-locked laser large enough to fit...

    2023-11-13
    Bekijk vertaling
  • AM Research has released its latest quarterly data and forecast report

    Recently, additive manufacturing research company AM Research released its latest quarterly data and forecast report, which deeply analyzes the latest developments in the global 3D printing market, covering multidimensional analysis of suppliers, printing technology, geographic location, and application areas.According to the report, the global 3D printing market once again demonstrates strong gro...

    2024-09-29
    Bekijk vertaling