I have an Algolaser DIY 20W and everything works normally. Recently, I bought a Delta 22W, and when performing the material test, I have this misalignment problem.I have already tried tightening the belts and checking for vibrations, but nothing, absolutely nothing works.Does anyone have any ideas on how to solve this?

Ruddy

02-20

204

8

0

I have a six month old sculpfun S30 22W. I have always used a kerf of 0.13mm outward when making boxes. Lately I have noticed that the joints are no longer as tight as they were at the beginning and I have to set the kerf to 0.20mm outward. Is this normal? Is there some setting somewhere, or has the beam gone out of focus?

Jack Wilborn

02-28

272

3

0

I’m only just getting started with LB, and I doubt this is actually a LB issue, but the number of passes does not seem to work like I would have expected.I have some experience with lasers and optics going back years.My expectation was that if I can get a 1mm deep cut on pass #1, I should get a bit less than 1mm again on pass 2. However that does...

Ethan

02-28

269

3

0

Preparation work before replacing laser machine partsBefore replacing laser machine components, it is necessary to first turn off the machine power and confirm the model and parameters of the components to be replaced. At the same time, suitable tools such as electrician pliers, screwdrivers, focusing cards, etc. should be prepared.Replace laser ...

Clarence

03-03

165

0

0

I have no problem putting text on a circle path. I can even figure out how to place it on the bottom and it be readable. My question is how do I remove the circle and the text stays curved? When using Framing, it creates a problem even if it is No Output and Not Visible selected. I think I did it once, but did not take notes.

Durell

02-27

148

2

0

Text misaligned using rotary roller

Hiroko

02-21

184

6

0

I have a 60W JPT EM7 MOPA Fiber laser and when I mark a circle, the top to bottom is shorter than the width. For example, I have a circle set to 2.625", but when I mark it, it comes out 2.625" wide x 2.531" tall. Any ideas on what to look at would be appreciated.

Erdogan

02-24

213

5

0

I have a design and want the stars and the other forms that now show as filled to be the areas that are not filled and the background area to be the fill. I tried to do some things with Offset shapes and no luck. Any ideas?

Noah

02-26

144

2

0

Skills and precautions for laser cutting of foam cottonFoam cotton is a kind of light, soft material with good sound insulation and shock resistance. It is widely used in electronics, instruments, communications, household appliances, automobiles, aviation and other fields. Foam cotton is usually processed by hand cutting or cutting tools, but thes...

Nugent

02-28

179

0

0

Wood is one of the most common processing materials for laser engraving. Laser engraving wood has the advantages of fine carving effect, accurate positioning, and no mechanical wear. With the help of intelligent control system, the processing plan can be flexibly adjusted to quickly complete personalized design. Therefore, it has a wide range of ap...

Liam

02-28

162

0

0

At present, large-scale fabric processing is mainly completed by knife cutting or laser cutting, and there are the following difficulties in the processing process:Soft deformation: The biggest characteristic of fabric is its softness and easy deformation, which makes it difficult to fix during cutting, resulting in difficulty in ensuring cutting...

roy

02-28

173

0

0

Acrylic is a widely used polymer plastic with a transparency of over 92% and excellent toughness and compression resistance, 9-17 times that of glass. It has a wide range of applications in various industries such as advertising display, building decoration, furniture, lighting fixtures, etc.Laser cutting of acrylic materials is prone to the foll...

Aaron

02-28

184

0

0

The fiber optic cutting control system is the control core of the fiber optic laser cutting machine. By sending signals to the laser and motor, the control system can accurately control the laser output and mechanical axis movement to complete the cutting and processing tasks. The fiber optic cutting system can also arrange the processing tasks, in...

Kevin

02-28

177

0

0

1. Laser powerPower directly affects the amount of melted powder and coating efficiency per unit time. When other working parameters are determined, low power may result in incomplete powder melting, pitting after polishing, insufficient bonding force, and low coating hardness; If the power is too high, it may be due to excessive melting of the mel...

Keegan

02-28

169

0

0

Precautions for using plastic laser welding machineBefore turning on the laser, ensure that there are no excess obstructions on the welding joint! Before powering on the system, please confirm that the welding joint mirror and fixture surface are clean and can be cleaned with specialized cleaning solutions such as anhydrous alcohol.When major abno...

Cyril

02-28

155

0

0