Torque motor is a special type of brushless permanent magnet synchronous motor. Since the load is directly connected to the rotor and no transmission parts are required, the torque motor belongs to the direct-drive motor.The following is the difference between torque motor and servo motor:Different performance1. Torque motor: a special mot...
2023-02-171.2K00Basic requirements1. High displacement accuracyDisplacement accuracy: refers to the compliance between the displacement of the machine tool workbench required by the command pulse and the actual displacement of the workbench converted by the servo system.2. Good stabilityStability: refers to that the servo system can reach a new or return t...
2023-02-171K001. Initialization parametersInitialize parameters before wiring. On the control card: select the control mode; Clear PID parameters to zero; When the control card is powered on, the enable signal is turned off by default; Save this state to ensure that the control card is in this state when it is powered on again.On the servo motor: set the...
2023-02-161K00What work needs to be done before starting the servo motor1) Measure the insulation resistance (not less than 0.5M for low-voltage motors).2) Measure the power supply voltage and check whether the motor wiring is correct and whether the power supply voltage meets the requirements.3) Check whether the starting equipment is in good condition.4)...
2023-02-161.1K00Daily maintenance of laser water chiller:1) Place the water chiller in a cool and ventilated place. It is recommended that the temperature be below 40 ℃. When using the laser chiller, the machine room should be kept clean and well ventilated, and the condenser should be cleaned regularly to ensure the normal operation of the unit.2) The wat...
2023-02-161.1K00Laser chillers are often used to cool UV lasers, CO2 laser glass tubes, semiconductor lasers, CO2 RF tube lasers, and fiber lasers of cutting machines, marking machines, engraving machines, and other equipment. Users can select suitable chillers according to different laser power. The installation and use of the laser chiller is very simple. The fi...
2023-02-1694700I power laser on and it only displays connecting to controller. I have disconnected the him from the controller and nothing homes. I have led 15 and 12 lit up with eithernet discounted. Homing switches work chiller input works and all drives are good no faults. Any ideas?
2023-02-021.2K20The servo in the industrial control industry is generally the abbreviation of AC servo system. At the project site, the servo we refer to is the servo driver. However, servo driver and servo motor are an inseparable system, and they are connected by encoder cable and power cable. Generally, the servo driver bears the control command of the controll...
2023-02-151.2K00How does the PLC control the servo motor to automatically move left and right The servo motor drives the linear module to move from the left to the right and then automatically returns
2023-02-1588310Introduce three control modes of servo motorIf you have no requirements for the speed and position of the motor, just output a constant torque, which of course is torque mode.If you have certain accuracy requirements for position and speed, but you don't care much about real-time torque, it is better to use speed or position mode.If the up...
2023-02-151.1K00Influence of gear type on noiseDifferent types of gears will have different meshing processes due to their different geometric characteristics. For example, under the condition of the same load and speed, through many application cases, it can be found that the noise of helical gear can be 3~10dB lower than that of spur gear;Influence of pr...
2023-02-151.1K00At the Photonics West Exhibition held in San Francisco from January 31 to February 2, ALIO Industries, the leading innovator of nano-precision motion control, will demonstrate its ability of accurate photon and fiber alignment applications at booth 4842.A glance at any industry vertical will show the increased use of LEDs and laser, optical...
2023-02-1592200In addition to the appearance structural parts of the foundation, the laser water chiller system mainly includes its internal refrigeration system and control system. The refrigeration system is generally composed of four parts: compressor, condenser, throttle valve, evaporator, etc; The control system includes the control of the compressor, thrott...
2023-02-141.1K00From the successful development of the first laser to the present, the laser is developing in the direction of high power and diversity. What is the future development trend of laser water chiller as a cooling equipment for laser?1、 Diversification.From the initial cooling of CO2, YAG and other traditional lasers to the current cooling of f...
2023-02-1496900Why is planetary reducer the "first choice" of servo motor? The PLE080 planetary reducer is usually used in combination with the servo motor to balance the inertia load conditions in frequent frequency cycle sequence, reduce the motor speed, improve the torque, and provide a solid mechanical interface for the pulley, cam, drum and other mechanical ...
2023-02-141K00
- 데이터 없음
한국어
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski