Do you know the reason why the 57 stepper motor and synchronous belt on the X-axis, which was just adjusted in the past two days, lost its step again?At the beginning, the tensioning structure of the synchronous belt was adjusted to ensure that the tensioning force of the synchronous belt was strong enough, but there were still cases of slipping.

Tim Johnson

2024-05-16

496

2

0

The modulus pressure angle and helix angle determine the pitch of the base circle, and adding the number of teeth determines the size of the base circle. The size of the base circle determines the shape of the involute. To understand the definition of modulus, it is actually a parameter that is close to a coefficient and cannot be directly measured...

LWE

2024-05-16

413

1

0

It is inevitable to encounter malfunctions when using industrial chillers. Below are several common malfunctions and their causes during the use of chillersOil pressure alarm occurs during useCommon causes of oil pressure alarm in chillers:1. The internal parts of the chiller have not been inspected and cleaned, resulting in oil stains, oil pump f...

Ruddy

2024-05-16

552

1

0

Laser marking is currently one of the most widely used laser processing technologies. Its principle is to use a highly concentrated laser beam to instantly evaporate part of the material surface, forming an indelible mark. Laser marking has the advantages of fast speed, good texture, and high accuracy, and has been widely used in many industries su...

Durell

2024-05-15

471

2

0

Hi, I have the Rudia RDC6563FG-Lite and have some questions about the controller, It says it supports 5v and 24v output limit switches and there is a Limit polarity setting for positive and negative on software but changing this setting cause no change and limit is only triggered by GND connection. Am I doing something wrong or is PNP not supported...

Juan Barkhuizen

2024-05-14

517

1

0

During use, the performance of a chiller will gradually decrease over time. In fact, many faults have some precursors before they occur, which are commonly referred to as potential faults.The failure rate of a chiller also varies over time, which is commonly referred to as its lifespan.1. Phase 1: Early FailureEarly failures, also known as the br...

Hiroko

2024-05-15

445

1

0

Laser marking is currently one of the most widely used marking and processing methods. The patterns or text produced by laser marking have a good texture and are indelible. They are often used in packaging, advertising, cables, consumer electronics and other products. Laser marking can be applied in both large-scale factories and small workshops, b...

Andrej

2024-05-15

446

1

0

1. Check the operating environment.Ensure that the water-cooled industrial chiller is placed in a well ventilated and temperature appropriate environment, avoiding direct sunlight or excessively humid environments, which helps the water-cooled industrial chiller maintain good working conditions.2. Check if the cooling water circulation system is ...

bernd.db

2024-05-14

475

1

0

Double speed chain transmission is a mechanical transmission device used for transmitting power and motion, mainly used for producing or transporting various materials through transmission. Of course, the main methods of double speed chain transmission include efficiency, reliability, and flexibility.1、 The Efficiency of Double Speed Chain Transm...

Iron Man

2024-05-14

541

1

0

Electric energy is one of the most important sources of energy in modern society, and motors are devices that convert electrical energy into mechanical energy. Electric motors are widely used in various industries such as machinery, metallurgy, petroleum, coal, chemistry, aviation, transportation, agriculture, and others. With the continuous improv...

berainlb

2024-05-14

466

1

0

In the field of material processing, laser technology has gradually become the preferred choice for industrial processing. Whether metal or non-metal materials, lasers can efficiently and accurately complete processing tasks, and achieve no deformation, small thermal reactions, and smooth edges. At present, laser processing tasks include cutting, c...

Patrick

2024-05-13

425

1

0

There are four main reasons for high gearbox noise:1. Internal tooth surface hardness of the reducerWith the development of gear hard tooth surface technology, its characteristics of large load-bearing capacity, small volume, light weight, and high transmission accuracy have made its application fields increasingly widespread. However, the carburiz...

jessie

2024-05-13

452

1

0

How to determine which gear is prone to fatigue pitting corrosion between the large and small gears in a pair of gear transmissions? Which gear is prone to bending fatigue fracture?

roy

2024-05-13

472

1

0

Laser marking machine is a high-precision device that can mark and engrave on various materials. However, sometimes we encounter problems with the xy axis of the laser marking machine not working, which can affect the normal use of the equipment. Let's analyze the cause and solution of this problem below.Firstly, the malfunction of the xy axis ma...

Payson

2024-05-11

470

1

0

With the continuous development of science and technology, laser technology has steadily developed in various industries, but laser welding machines have appeared in our lives, such as stainless steel, aluminum (home, cabinets, kitchens and bathrooms, stairs and elevators, shelves, ovens, doors, windows, guardrails, distribution boxes), etc. Howeve...

Vasili

2024-05-11

471

1

0