Français

Scientists are using lasers to create lunar paving blocks

865
2023-10-14 10:46:24
Voir la traduction

Original Hal Bowman 9000 Scientific Razor
The 3 kW laser power output on a 45 mm laser spot consolidates the interlocking structure within the EAC-1A powder bed. Source: Jens Kinst, BAM

By using lasers to melt lunar soil into stronger layered materials, it is possible to build paved roads and landing pads on the moon, according to a concept validation study in a scientific report. Although these experiments were conducted on Earth using alternatives to lunar dust, these findings demonstrate the feasibility of the technology and indicate that it can be replicated on the moon. However, according to the author, further work may be needed to improve this process.

Lunar dust poses a significant challenge to lunar rovers, as due to low gravity levels, they often float around and may damage equipment when disturbed. Therefore, infrastructure such as roads and landing pads is crucial for alleviating dust problems and promoting lunar transportation. However, the cost of transporting building materials from Earth is high, making the use of available resources on the moon crucial.

Gin é s Palomares, Miranda Fateri, and Jens G ü nster used carbon dioxide lasers to melt a fine-grained material called EAC-1A (developed by ESA as a substitute for lunar soil) to simulate how lunar dust melts into solid matter through focused solar radiation on the moon.

The author attempted laser beams of different intensities and sizes (up to 12 kW and 100 mm respectively) to create sturdy materials, although they determined that intersecting or overlapping laser beam paths could lead to cracking. They developed a strategy to use a laser beam with a diameter of 45 millimeters to generate a triangular, hollow geometric shape about 250 millimeters in size. The author suggests that these can be interlocked to form a sturdy surface on a large area of lunar soil, which can serve as roads and landing pads.

Rendered images of roads and landing pads paved on the lunar surface. Source: Liquifer Systems Group


In order to reproduce this method on the moon, the author calculated that approximately 2.37 square meters of lenses need to be transported from Earth to replace lasers as solar concentrators. The relatively small equipment size required will be an advantage for future lunar missions.

Source: Yangtze River Delta Laser Alliance

Recommandations associées
  • Quantum computing company secures $500 million in funding

    Quantum Computing Inc. (QCI), a startup based in the United States, recently opened a foundry for integrating photonics with thin-film lithium niobate (TFLN). The company announced that it has raised $500 million in total proceeds through a new private equity offering.It means that the Nasdaq-listed New Jersey startup, whose foundry is located within Arizona State University’s Research Park in Tem...

    09-30
    Voir la traduction
  • UK to Build World's Largest Power Laser: Accelerating the Use of Nuclear Fusion and Promising to Obtain Clean Energy

    According to reports, British scientists will build the world's largest power laser. They hope that this £ 85 million (approximately $103 million) device can accelerate the use of nuclear fusion and potentially obtain clean energy, which is inexhaustible.According to the report, the "Vulcan" 20-20 laser will be built in Havel, Oxfordshire, and it will produce a laser brightness that is 24 t...

    2023-10-09
    Voir la traduction
  • The technological iteration route of automotive millimeter wave radar chips

    The rapid development of intelligent cars and autonomous driving technology has made millimeter wave radar inconspicuous, and the widespread application of millimeter wave radar has driven the technological evolution of MMIC.From the expensive gallium arsenide (GaAs) process in the early days to the mainstream CMOS and SiGe processes today, and then to the future promising FD-SOI process, the cont...

    2024-12-07
    Voir la traduction
  • What are the "unique secrets" of each family in terms of breaking the game and high reaction materials?

    Laser is considered a sharp sword that cuts iron like mud, but even sharper swords can have tricky moments. For example, in certain scenarios, there are materials with higher reflectivity, such as silver, copper, etc., known as "high reflection materials". High reflective materials have a low absorption rate for lasers, making them difficult to process and potentially causing equipment failure or ...

    2023-11-06
    Voir la traduction
  • The output power of high power femtosecond laser breaking through the key bottleneck of average power can reach the order of 100 watts

    High energy, high average power femtosecond laser due to the attosecond high order harmonic generation, precision processing and manufacturing, biomedical and national defense and other fields of extensive application needs, is the forefront of ultrafast super laser technology research in the past decade.Especially fiber laser due to stable and reliable operation characteristics, compact structure...

    2023-09-04
    Voir la traduction