Français

Shanghai Institute of Optics and Fine Mechanics has made progress in synchronously pumped ultrafast Raman fiber lasers

270
2025-06-07 10:47:47
Voir la traduction

Recently, the research team led by Zhou Jiaqi from the Aerospace Laser Technology and Systems Department of the Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, has made progress in the study of synchronously pumped ultrafast Raman fiber lasers. The related achievements were published in Optics Express under the title "Revealing influence of timing jitter on ultra fast Raman fiber laser synchronously pumped by gain switched diode".

Synchronous pumping technology utilizes ultrafast pulses with high peak power as pumps. Compared to traditional mode-locked Raman fiber lasers with continuous optical pumping, it can effectively overcome the problem of weak Raman gain and obtain high-performance Raman solitons under short cavity conditions. For synchronously pumped Raman fiber lasers, using a gain switching diode (GSD) with adjustable repetition rate as the pump can effectively simplify the synchronization difficulty compared to a mode-locked pump source with fixed repetition rate.

The research team built a GSD synchronously pumped Raman fiber laser (Figure 1), and the experimental results revealed that the inherent strong time jitter characteristics of GSD pump pulses are the fundamental reason for reducing the time-domain stability and frequency-domain coherence of output Raman pulses. A detailed study was conducted on the time-frequency characteristics of output Raman pulses under different pump pulse widths, confirming that stretching the pulse width can effectively reduce the influence of pump time jitter and suppress the relative intensity noise of output Raman pulses (Figure 2). In addition, comparative experiments were conducted using a mode-locked laser instead of GSD pump, and the results further confirmed the key influence of pump pulse time jitter on the frequency domain coherence of output Raman pulses. This study not only deepens the understanding of GSD synchronously pumped Raman fiber lasers, but also paves the way for the generation of high-performance ultrafast Raman pulses.


Figure 1. Schematic diagram of experimental setup for GSD synchronously pumped Raman fiber laser


Figure 2. Relative intensity noise of output Raman pulses under different pumping conditions


Relevant work has been supported by the National Key R&D Program, the Youth Innovation Promotion Association of the Chinese Academy of Sciences, the National Natural Science Foundation of China and other projects.

Source: Opticsky

Recommandations associées
  • High sensitivity visualization of ultrafast carrier diffusion using a wide field holographic microscope

    A sketch of the imaging and holographic parts of a transient holographic microscope, including a pulse sequence, to illustrate the signal modulation method. By imaging the pinhole array at the sample position, a diffraction limited excitation spot array can be created, allowing for the simultaneous collection of transient data around 100 excitation spots.Femtosecond transient microscopy is an impo...

    2023-12-25
    Voir la traduction
  • The latest progress in laser chip manufacturing

    Modern computer chips can construct nanoscale structures. So far, only these tiny structures can be formed on top of silicon chips, but now a new technology can create nanoscale structures in a layer beneath the surface. The inventor of this method stated that it has broad application prospects in the fields of photonics and electronics, and one day, people can manufacture 3D structures on the ent...

    2024-07-29
    Voir la traduction
  • The United States promotes the development of next-generation EUV lithography technology

    LLNL has long been a pioneer in the development of EUV lithography technology.A laboratory located in California will lay the foundation for the next development of extreme ultraviolet (EUV) lithography technology. The project is led by Lawrence Livermore National Laboratory (LLNL) and aims to promote the next development of EUV lithography technology, centered around the laboratory's developed dr...

    01-06
    Voir la traduction
  • 3D printed nanocellulose for green building applications

    The hydrogel material made of nano cellulose and algae was tested as an alternative and more environmentally friendly building material for the first time. This study from Chalmers Institute of Technology and the Wallenburg Wood Science Center in Sweden demonstrates how to 3D print rich sustainable materials into various building components, using much less energy than traditional building methods...

    2024-02-19
    Voir la traduction
  • Xiaomi has recently invented a laser engraving machine that allows you to create screen printing and design using different materials

    3D printers have become popular worldwide, allowing you to create useful and beautiful products. This has sparked a trend towards DIY, which is "doing it yourself," even driving popular pages such as Etsy in Spain. In fact, an economy has been established around these types of handmade products. But there are more devices that can help with these types of creativity.The latest one is Xiaomi's inve...

    2023-12-26
    Voir la traduction