I have traced a descent sized image in terms of L x W, so that the Trace Image feature can grab as much detail as it can.When scaling down the traced image, part of the trace disappears and there is a disconnect which can only be seen in the preview tab.Image preview when making the trace bigger and there is no disconnect:How can I make sure th...

Smith

2023-08-25

456

1

0

What does sanity check do?

Miller

2023-08-25

586

1

0

No matter how large I make the ‘Y Center’ or ‘X Center’, the generator keeps this tiny space between the cuts squares. Take a look at the screenshot. I need that gap to be larger otherwise the laser just cuts into the next line.

Darren

2023-08-25

550

1

0

HII would like to understand why the preview of the photos almost never corresponds to the final result.Show the photo always much darker and therefore you are forced to experiment, wasting a lot of time and material consumption.Solutions?

David

2023-08-24

521

1

0

New getting Missed Steps. Got a hold down magnet (quite powerful) on Stepper Motor, and also gantry obstructed on home.The belts are OK, steps only Y mainly I think…Could there be missing teeth - does not always occur.Are there settings that I could change to helpLawrence

Abel

2023-08-25

437

1

0

This is my question: I’m drawing in inkscape paths in differents colors. The closed path can be rustered, so the question is: can engrave grayscale background with “proportional power” like image engrave function?

Williams

2023-08-25

571

1

0

I am just starting to use Lightburn software and it is not as friendly as it seems when I watch the hours for videos.I am trying to cut the corner off of a piece of wood.I just the pencil to draw a straight line then use the same settings as I did with a rectangle key chain.But, the laser just lightly scores the wood and will not slow and cut.What...

jessie

2023-08-17

614

1

0

Hello what is the best configuration to record in glass with ink, stanley cups or similar, thermal cups, I want to know what is the best configuration using EZCAD SOFTWARE, to record in stainless steel cups with ink, someone can help me???

A72 pro

2023-08-12

635

2

0

Im getting a noticeable wobble in my x axis?I’m a bit lost on what to do since the belt is pretty tight already.

jessie

2023-08-14

617

1

0

I was cutting and engraving 1/8 ply when my settings changed from 90/20 to .3/55. Cutting and engraving speeds are all less than 10mm/s. I have reloaded the cut library and redownloaded one as well. Still nothing. It changed all of the settings in the library with speeds starting 0.xxx. Any advice is appreciated.

Vasili

2023-08-11

641

1

0

When I use lightburn’s matrix option there is a risk when the engraver goes to work on the other duplicate design.If I send it to record individually, the problem doesn’t happen.Can someone help me, please?

Nugent

2023-08-11

573

1

0

Question regarding filled lines: when burning rectangles (and circles) Lightburn sends the laser side to side.This is great for the filled lines parallel to the laser travel (left and right) but not so good for vertical filled lines, it takes a lot of time for the verticals. It burns a tiny piece of one end, travels across and then burns a tiny pie...

Payson

2023-08-11

511

1

0

My setup consists of my workshop bench (fixed) with an array of 20mm dog holes MFT like. My main laser is a much upgraded S9 with a y-axis extension. Above the bench I have a wide angle LightBurn Camera. The laser is mounted via fixation devices that use the dog holes. After doing alignment I find that I can put the laser away and get it back to th...

Robert Evans

2023-08-04

492

1

0

Hi All,I am a few weeks into using the trial version of Lightburn with a Genmitsu 4040-Pro. I’ve had a great time with it to-date, until today.I have everything set on my trusty MacBook Pro. I prefer the Mac when designing and for general use. Today, I needed to get work done so I had the idea to set up Lightroom on a fairly new PC laptop. T...

Terrelle

2023-08-11

622

1

0

everything worked fine for day one. then day 2 the x axis is now backwards where I use move function with the left arrow and moves in the negatives coordinates but it moves to the laser to the right on my 3d printer. at startup sometimes it will say hard limit triggered other times it will not and say homing ok. I wrote an email for support and did...

John Trant

2023-08-04

542

1

0