Pixel Voltaic, a subsidiary of the University of Porto, has launched a laser system for sealing glass and fiberglass perovskite photovoltaic modules, with a maximum size of 30 cm x 30 cm. The company's technology roadmap is to increase production capacity to accommodate larger equipment areas of up to 1 square meter and modify processes to operate ...

Jen

2024-02-14

733

1

1

Programmable photonic integrated circuits process light waves used for computation, sensing, and signal transmission in a programmable manner to meet different requirements. Researchers from the Gyeongsangbuk Institute of Science and Technology in Daegu, South Korea, and collaborators from the Korean Academy of Science and Technology have made sign...

Liam

2024-02-12

707

1

0

Laser Research Optics has launched a series of ZnSe laser focusing lenses for steel cutting lasers up to 4kW, used for cutting thick diamond slabs and other heavy steel products.Laser Research CO2 focusing lenses have an outer diameter size of 1 "to 2.5" and a focal length of 5 "to 10" with increments of 0.5 "to meet specific steel cutting requir...

roy

2024-02-12

711

1

1

China is striving to develop laser communication technology, which is a key component of space-based information networks.In a recent development, the country has launched its first bidirectional laser communication terminal into space for technological demonstration.The experimental terminal was developed by HiStarlink, a private laser co...

jessie

2024-02-11

631

1

1

Researchers at Tokyo Metropolitan University have proposed a new method of rolling atomic thin sheets into "nanoreels". Their unique method uses transition metal chalcogenide sheets with different compositions on both sides to achieve tight rolling, with a center diameter as small as 5 nanometers and a length as small as micrometers. The control of...

Patrick

2024-02-11

585

1

0

Deep Space Station 13, located at NASA's Goldstone Deep Space Communication Center near Basto, California, is part of the agency's deep space network. It is a 34 meter experimental antenna that has been modified with an optical terminal (a square instrument located below the center of the antenna dish).Since November 2023, DSS-13 has been t...

Carey

2024-02-15

671

0

0

Lightburn boots OK and works for a while. Then it gets into a mode where double clicking on the e.g. cut/layers menu comes up for a fraction of a second, and then disappears. If I click on Windows to see where it might have gone, I can only click on that oonce and then it disappears. Any thoughts?

David

2024-01-31

654

1

1

My camera window takes up entire screen and I cant move, shrink, or close it. Any way to reset it?

Nugent

2024-01-25

678

2

0

I am running an Atomstack X20 Pro and I tried to install the rotary to do glasses. I have completly messed up the controller settings. My laser isn’t framing or firing and keeps bashing against the rails. Is there a factory reset on the machine? I need to start again as I have done something very wrong.

Vasili

2024-01-25

661

2

0

I just wasted this morning fighting with a non-existent laser problem!Somehow LightBurn “Start from” got changed from “Absolute coords” to “Current Position”. Since I always work in Absolute coordinates I did not even think to check this setting.Is there a way I can get LightBurn to always start in Absolute coord...

Payson

2024-01-25

730

1

1

Gas analysis is a key technology used to identify and control pollution in the optoelectronic production process, which can avoid equipment defects, economic losses, and reduce safety risks. This article explores the importance of pollution control in optoelectronic manufacturing, gas analysis techniques, applications, and the latest developments....

JOST

2024-01-24

666

1

0

On the main window I have my preferences to inches. The grid on side and top do not have a inch between them how do I change the grid where I can see every inch space hope this makes sense thanks Dennis.

Cruise Wang

2024-01-24

759

2

0

I am importing a shape from a dxf file that includes the line and associated fill. When imported the fill is removed with only the line element showing. How are drawing elements with fill (solid/hatch) imported into LightBurn to retain the fill? Also, how are images imported into LightBurn so the background is transparent? Is there a way to add fil...

Carey

2024-01-24

681

1

0

Hi guys,From the picture you can see that the cut is not straight along the Y axis but the cut along the X axis is straight! Not sure how the fix because if it was the lens focus issue the cut along the X axis wouldn’t be straight as well, right?I’m using a 2" lens, 90w CO2 laser , the material I’m cutting it’s a 5mm acrylic...

Erdogan

2024-01-23

746

1

0

Can the Cut Pallete settings be set permanently? and NOT let the projects overwrite the Cut Pallete?Or at least an option to turn this feature off?

Ruddy

2024-01-23

620

1

0