I recently bought a new 100w power supply for my 90w Cloudray tube. The power supply has a remote adjustment for power. I find that I cut paper to cardboard to engrave and cutting that all take different power settings. I don’t like to blast thru materials at full power. So from Lightburn I could need various files of the exact same vector to...

Jamie

2023-12-09

682

1

0

Laser chillers are mainly used in laser processing equipment such as laser marking machines, laser engraving machines, laser welding machines, laser code spraying machines, laser cutting machines, etc. They can accurately control the temperature required by the laser equipment, thereby ensuring the normal operation of the laser equipment. How can w...

jessie

2023-11-21

683

1

0

Laser chillers are commonly used to cool lasers in cutting machines, marking machines, engraving machines, and other equipment. During use, some malfunctions may occur. How can we solve the problem of high condensation pressure in laser chillers? Firstly, we need to understand that stress is only a superficial phenomenon, and we need to deeply unde...

jessie

2023-11-21

833

1

0

Hi there!I wanted to see if I can have some help with my engraving. I’m using an ORTUR laser to engrave my yeti cups. I’ve engraved over 30 WHITE cups and everything turned out fine until I needed to engrave a black one. I don’t understand why it’s not working. I decreased the speed and set the power to a higher setting. I e...

Christian

2023-11-21

729

1

0

I’m trying to figure out how to laser on each side of a hex bar with six flat sides with 6 different patterns been trying to find a video but nothing. please and help

Nugent

2023-11-21

742

1

0

Since LB can not create a spiral easily, I made one in Inkscape and then placed it in LB.I then applied text to path, which works, but its written from the center out.I need it to be written from the outside.But nothing I do will get it to do that.I figured the answer to this would be the Set Shape Start Point tool.Which if I use that, it will plac...

Payson

2023-11-20

1K

1

0

Hello. I have an OML3 and would like to know how to control air assist from lightburn so the air flows when cutting and stop while engraving without me having to turn my pump on and off manually. I need to know about configiuration and hardware needed for this if it is possible. Thanks.

Terrelle

2023-11-20

743

1

0

I’ve been doing experiments with Image engraving. I’ve done a lot of my general fill engraving to high DPI (usually as high as 600). But two things occurred to me. 1.) after doing a proper DPI test based on an Imag-R file, I found that my machines DPI is roughly 242-254. Though, I just realized that this was based on Image Pass-Through ...

Clarence

2023-11-20

849

1

0

On November 16th, the cumulative delivery of Innovusion high-performance LiDAR in the car market exceeded 200,000 units as of November this year, according to Innovusion. At present, the production capacity of Innovusion has exceeded 300,000 units per year, and a new production line is also being laid out, which will usher in the mass production st...

Gilbert

2023-11-17

835

1

0

Corto MDF e outros materiais com facilidade, mas o EVA branco da muito trabalho para cortar, corto todas as outras cores normalmente mas em especifico a cor branca da muito trabalho. Tenho que colocar uma potencia bem reduzida e com a potencia no máximo para cortar, e o acabamento ainda n sai bom. Se alguém puder me ajudar com alguma ...

Cyril

2023-11-17

773

1

0

Is there a way to rotate the camera view window? It’s always 90° off even in the calibration. Thanks.

Darren

2023-11-17

968

1

0

Do you need to actiuvate RDcutist software to use it ?

Cityslicker

2023-11-15

848

3

0

I have an atomstack A20 with an R3 rotary. The R3 rotary plugs in place of the Y axis.I have an SVG that cuts perfectly fine on a flat plane, but when I swap the Y axis for the rotary (using the same gcode, not using any rotary feature in lightburn) it gets garbled in the X axis. I have no clue what is going on.

Abel

2023-11-16

988

1

0

Hola , mi maquina al momento de grabar una imagen me indica el tiempo de demora ejemplo; 4 minutos, pero en práctica no es así y se demora una hora en grabar una pequeña imagen de 40x40 mm.

Williams

2023-11-16

864

1

0

SM Cinema set up SM IMAX Iloilo, showcasing the brand-new IMAX® With Laser, which is the next generation of laser projection and multi-channel sound system that provides crystal clear, realistic images and precise audio, bringing a unique viewing experience.The new system debuted with the release of The Hunger Games: The Ballad of Songbirds an...

Smith

2023-11-16

726

1

0