I have seen a device that controls the servo directly through the screen. It should be a special address register for communication. But I want to know how to do it, including parameter setting.

Payson

2023-03-15

878

1

0

Hey there! I bought an FTG rotary, and hooked up to the Y axis on the Lightburn compatible board that came installed in my Monport Blue K40. The machine is working with standard flat burning, so supposedly everything is fine until I swap to the rotary. When I power up, the machine does its Double Homing Routine (once quick, backs off and then does ...

Liam

2023-03-14

1K

1

0

Hi guys, I have a Gweike Cloud RF and have had to set my scan off-set in lightburn for 300mm/s at 1.49 mm to remain inside the object I am engraving. This sounds quite a large scan off-set. Can anyone share what off-sets they are using at different speeds. Gweike online help was pretty vague to say the least.

Simon

2023-03-14

1.2K

2

0

In the continuous production process of the injection molding machine, the mold needs to be cooled to shorten its setting time and improve its accuracy. What should we pay attention to when selecting industrial water chillers for injection molding machines?The cooling capacity of the selected chiller directly affects the normal use of produ...

Henry

2023-03-14

810

0

0

Mitsubishi JE servo pulse control. The program logic has been verified to be correct. Now the position of the equipment is not allowed to exceed the range after about ten minutes of operation. The monitoring Mitsubishi motor command pulse accumulation has drifted up. Later, the filter has been added to improve it. After grounding 0V, the single ser...

Payson

2023-03-13

918

1

0

How to control the stepper motor to realize intermittent feed motion by xinjie plc.

Nugent

2023-03-13

1K

1

0

I’m making a small drawstring bag.I created a rectangle 100mm x 140mm. I then put a radius of 50mm on the bottom 2 corners making a cup or shield sort of shape (rounded bottom of the bag). Then I created a tool layer (T2) by using the Offset Shapes tool and shrinking by 4 to create my stitch line. Using the Edit Nodes tool, I deleted the top...

Smith

2023-03-13

897

1

0

Lightburn up to date 1.3.01 and now the laser when framing is going ballistic grinding and not framing right. I have projects to do on a time line and if Lightburn will not run when I need it maybe I need to find another software.

Darren

2023-03-13

1.2K

1

0

My laser burns some extra lines in text. Using Genmitsu 3018 router with laser attachment.

Gilbert

2023-03-13

1K

1

0

One equipment on the production line and one servo are transplanted to the normal position. It has been determined that there is no problem with the mechanism. It should be an interference problem. The servo is Panasonic servo motor. I don't know how to eliminate this problem?

Vasili

2023-03-13

986

1

0

is there a simple setting for when you rotate text 90 degrees? can i switch the scan direction to move y axis first then the x? when i rotate the text, and there is space between lines, the laser has to travel across those blank spaces just to make one small tick, then move on. seems would be faster to scan across the line of text rather than up/do...

Simon

2023-03-10

969

1

0

Hi guys,I’ve been using Lightburn for some time now with my 50w JPT Fiber laser.I’ve just recently installed and setup my rotary, my problem is once I have successfully setup the rotary for the current project and run project, then saved it for multiple runs. I then create a new project which requires a different rotary config, set tha...

Jen

2023-03-10

1K

1

0

I have a project where I have to burn off black paint from a plexiglass. (a transparent scale for a tank with liquid) I got a sheet of transparent, fully clear, not matte, plexiglass (acrylic glass) I spray painted it with black paint (have two choices, from a spray can, of can use an airbrush and paint it with water based acrylic paint, same resul...

John Trant

2023-03-10

1K

1

0

Does Lightburn save the calculated cut path optimizations in the file? Can it? Or, does it have to recalculate them every time I run the file? I’m on LB 1.3.01 on Ubuntu 22.04.

Jamie

2023-03-10

1.1K

1

0

The can is broken, and the pressure is rhythmic. This is the hydraulic part.On the other hand, the servo motor follows the rhythm of the energy storage tank and goes off and on.Oil and electricity are irrelevant.

Keegan

2023-03-10

1K

1

0