Español

Feasibility Study on Composite Manufacturing of Laser Powder Bed Melting and Cold Casting

490
2024-06-06 14:46:49
Ver traducción

It is reported that researchers from the Technical University of Munich in Germany have reported a feasibility study on the composite manufacturing of EN AC-42000 alloy by combining laser powder bed melting and cold casting. The related research titled "Feasibility study on hybrid manufacturing combining laser based powder bed fusion and chill casting on the example of EN AC-42000 alloy" was published in Materials Science and Engineering Technology.

 



Laser based powder bed melting can be combined with casting to form a composite manufacturing process. This is to simultaneously utilize the advantages of both processes. In order to investigate the challenges associated with the use of aluminum alloys, researchers first conducted experiments using two common independent processes, the alloy EN AC-42000. Place the EN AC-42000 alloy samples that have undergone different surface treatments into a sand mold, and then cast them onto the aluminum melt. The contact area between the partially melted insert and the casting material was examined using an optical microscope. The results indicate that the main challenges include binding issues caused by the presence of oxides and high porosity. The high porosity can be traced back to the increase in porosity of inserts during laser powder bed melting.

 


Figure 1: Composite casting aims to combine the advantages of laser powder melting and die casting.

 


Figure 2: a) Experimental method scheme. The cylindrical aluminum sample is completely cast in. b) The image of inserting the sample into the four tubes inside the sand mold for the casting process.

 


Figure 3: Overview of samples after cutting, grinding, and polishing.

 


Figure 4: Microscopic image of the sample: Visible contact surfaces and pores are depicted in areas 1 and 2. The enlarged area 2 attempts to capture evidence of metal fusion or non fusion.

The purpose of this study is to gain a preliminary understanding of the challenges faced in combining laser powder bed melt additive manufacturing with casting. The results indicate that the porosity of EN AC-42000 alloy significantly increases. The increase in porosity is a major issue in the feasibility of the process, and further research should be conducted on possible solutions to prevent a significant increase in porosity.

In addition to porosity, there is also a certain degree of material fusion between castings and inserts manufactured by laser powder bed melting. In terms of process feasibility, these results mean that the oxide layer needs to be thoroughly removed and prevented from re growing after removal. In further research, methods for removing the oxide layer and stabilizing this deoxygenation state should be explored to make them suitable for components manufactured by laser powder bed melting.

Paper link: https://doi.org/10.1002/mawe.202300403

Source: Yangtze River Delta Laser Alliance

Recomendaciones relacionadas
  • Scientists have developed the most powerful ultraviolet laser using LBO crystals

    It is reported that recently researchers from the Chinese Academy of Sciences have achieved the highest power output of 193 nm and 221 nm lasers using lithium borate (LBO) crystals. This achievement lays the foundation for the further application of the laser in deep ultraviolet (DUV) spectroscopy.The laser in DUV spectroscopy has many applications in science and technology, such as defect detecti...

    2024-04-07
    Ver traducción
  • Using high-speed scanning remelting technology to achieve AlSi10Mg laser powder bed fusion with excellent strength and plasticity properties

    The development of additive manufacturing (AM) has profoundly changed the manufacturing industry, and this technology has been applied in fields such as food, medicine, automotive, and electronic components. Especially in the aerospace field, where extremely lightweight and high-strength (~500mpa) components are required, aluminum alloy additive manufacturing is considered a very promising solutio...

    2024-10-08
    Ver traducción
  • Researchers improve laser behavior by tying laser knots

    Researchers have created a new type of laser that, despite environmental noise and manufacturing defects, still performs as expected. Technically speaking, researchers have created a topology, time, and mode-locked laser. This study has the potential to improve sensors and computing hardware.A mode-locked laser emits light with regular pulses instead of a continuous beam. Pulses can be very counta...

    2024-03-07
    Ver traducción
  • Researchers use liquid metal and laser ablation to create stretchable micro antennas

    Researchers have developed a new method of making micro stretchable antenna with water gel and liquid metal. These antennas can be used for wearable and flexible wireless electronic devices to provide links between devices and external systems for power transmission, data processing, and communication.Using our new manufacturing method, we have demonstrated that the length of liquid metal antennas...

    2023-09-19
    Ver traducción
  • Amazemet uses Siemens Xcelerator software for scaling metal 3D printing

    Polish metal 3D printing company Amazemet uses the Xcelerator software combination from industrial manufacturing company Siemens.The spin off company of Warsaw University of Technology is using Siemens workflow management software to develop its metal powder atomizer and 3D printing post-processing equipment.Amazemet was founded in 2016, and its ultrasonic atomization device is capable of producin...

    2024-04-18
    Ver traducción