Español

Research has found that inorganic perovskite materials are easy to prepare and process, making them suitable for manufacturing lasers

531
2024-01-04 14:19:29
Ver traducción

According to research from Busan National University, inorganic perovskite materials are easy to prepare and process, making them suitable for manufacturing lasers.
The perovskite of interest is CsPbBr3, which must form "nanosheets" within the specific structure invented by the Busan team to obtain sufficient laser gain.

It is not that the laser has been achieved, as the research project aims to characterize these nanosheets in terms of gain, temperature, and other parameters to provide data for designing future lasers.

According to the university, the team "achieved enhanced signal amplification in nanosheets through unique waveguide patterns, thereby enhancing gain and thermal stability.". These advances have had a wide-ranging impact on the applications of lasers, sensors, and solar cells, and may also affect areas such as environmental monitoring, industrial processes, and healthcare.

Under appropriate conditions, CsPbBr3 spontaneously forms atomic thick squares at around 150nm across the solution. Atomic level fine dust - quantum dots - are another form that can spontaneously form, but so far they have not provided sufficient gain for lasers.

Using micro imprinting lithography technology, waveguides were formed on a 20 x 20mm polyurethane acrylic substrate - a series of 20 μ M wide, 20 μ A long parallel channel with a depth of m, separated by 20 μ M thick wall.
These channels are filled with CsPbBr3 precursor solution and carefully wiped multiple times with a blade to evenly dose each channel.

The subsequent drying left a polycrystalline nanosheet at the bottom of each channel, which can be used for optical analysis - this is the expertise of the Busan Laboratory: the Department of Optoelectronics and Cogno Electromechanical Engineering.

"Perovskite nanosheets have properties that make them valuable for various applications," the university said. Their achievements have overcome the shortcomings of CsPbBr3 quantum dots, as their gain is essentially limited due to the short decay time of population inversion.

As part of the results, researchers created a new metric - "gain profile" - which describes the relationship between gain, spectral energy, and stripe length, and is "very convenient for analyzing local gain changes," according to the university.

The excitation and temperature dependence of the gain profile were measured, and the increase in gain and thermal stability of the polyurethane acrylate waveguide on the nanosheets was quantified.

"This enhancement is attributed to the improvement of optical constraints and heat dissipation, which is promoted by two-dimensional centroid constrained excitons and local states caused by uneven sheet thickness and defect states," said Pusan.

The collaboration between Busan National University and Oxford University in South Korea led to the publication of research results in the journal Optics: Science and Applications, titled "Enhancing perovskite nanosheets through patterned waveguides: excitation and temperature dependence of gain saturation.".

Source: Laser Net



Recomendaciones relacionadas
  • Significant progress made in 808nm high-power semiconductor laser chips

    The R&D team of Xi'an Lixin Optoelectronics Technology Co., Ltd. (hereinafter referred to as "Lixin Optoelectronics") has made significant progress in 808nm high-power semiconductor laser chips through continuous technological breakthroughs.808nm semiconductor laser, as an ideal and efficient solid-state laser pump source, plays an important role in advanced manufacturing, mechanical processin...

    2024-06-14
    Ver traducción
  • Progress in Calibration of Large Aperture Diffractive Lenses in the High Power Laser Physics Joint Laboratory of Shanghai Institute of Optics and Mechanics

    Recently, the High Power Laser Physics Joint Laboratory of Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, proposed a single exposure interferometric calibration method for large aperture diffractive lenses, which provides strong support for the engineering application of large aperture diffractive lenses. The relevant achievements are published in Optics Letters as "...

    2023-10-14
    Ver traducción
  • Southeast University makes new progress in quantum efficiency research of van der Waals light-emitting diodes

    Recently, Professor Ni Zhenhua from the School of Electronic Science and Engineering at Southeast University, Professor Lv Junpeng from the School of Physics, Professor Liu Hongwei from the School of Physical Science and Technology at Nanjing Normal University, and Professor Zhou Peng from the School of Microelectronics at Fudan University collaborated to propose a van der Waals light-emitting dio...

    2024-10-28
    Ver traducción
  • Which automotive parts can use laser soldering technology

    Laser soldering is widely used in the manufacturing of automotive parts. Here are some common automotive parts that can be welded using laser soldering:Automotive electronic control systemEngine Control Unit (ECU): The engine control unit is the "brain" of the car engine, which receives signals from various sensors and controls the operation of the engine based on these signals. Laser soldering ca...

    02-10
    Ver traducción
  • 253 million US dollars! This Canadian medical fiber optic sensor manufacturer will be acquired

    Recently, Haemantics Corporation, which focuses on providing innovative medical solutions with proprietary optical technology, announced that the company has reached a final agreement. According to the agreement, Haemonics will acquire all outstanding shares of Canadian fiber optic sensor manufacturer OpSens for CAD 2.90 per share.This is an all cash transaction with a fully diluted equity value o...

    2023-10-18
    Ver traducción