Español

Photon chips help drones fly unobstructed in weak signal areas

931
2023-10-28 09:58:39
Ver traducción

With funding from the National Science Foundation of the United States, researchers at the University of Rochester are developing photonic chips that use quantum technology called "weak value amplification" to replace mechanical gyroscopes used in drones, enabling them to fly in areas where GPS signals are obstructed or unavailable.

Using this quantum technology, scientists aim to provide the same sensitivity level as large optical gyroscopes on small handheld photonic chips, which may alter the navigation of drones.

Jaime Cardenas, an associate professor at the Institute of Optics, has received a new National Science Foundation grant to develop this chip by 2026.

Cardenas stated that the fiber optic gyroscopes currently used on the most advanced drones include several kilometers of fiber optic spools or have limited dynamic range.

At present, the sensitivity and stability of gyroscopes must be fundamentally balanced between their size and weight. As unmanned aerial vehicles, drones, and satellites become smaller and more common, the demand for ultra compact navigation level gyroscopes will become crucial. The most advanced micro gyroscopes are compact and sturdy, but their performance is insufficient, which hinders their application in navigation.

According to Cardenas, weak amplification has more advantages than traditional methods because it can enhance the interference measurement signal without the cost of amplifying several forms of technical noise. But the previous weak amplification demonstration required complex laboratory settings and precise calibration; Cardenas is committed to achieving weak amplification on micro photonic chips using high-quality factor ring resonators.

Cardenas' collaborators in this project include physicist Andrew Jordan, who was a former faculty member at the University of Rochester and currently works at Chapman University. Cardenas stated that he will also collaborate with the David T. Kearns Leadership and Diversity Center at the university to expand the participation of underrepresented groups and stimulate their desire for STEM careers through research experience with high school students in the Rochester City school district.

Source: OFweek

Recomendaciones relacionadas
  • Opton Laser commercializes ultra-high contrast third-order autocorrelators

    Recently, Opton Laser International, a supplier specializing in photonics, is currently distributing manufacturer UltraFast Innovations (UFI)'s ultra-high contrast third-order autocorrelator Tundra++. The new generation Tundra aims to characterize the temporal intensity distribution and quality of laser pulses with particularly high sensitivity.This is to avoid the harmful effects caused by the hi...

    2023-08-31
    Ver traducción
  • LASIT's Laser Revolution: Illuminating the Path to a Greener Future

    In the breakthrough transformation towards sustainable industrial practices, LASIT is at the forefront of the ecological revolution in laser marking technology. This evolution is not just about labeling products; This is about marking a sustainable future.Environmental Innovation: A New Era of Industrial PrecisionLASIT's laser technology is a model of environmental protection. Unlike traditional m...

    2023-11-28
    Ver traducción
  • TDK introduces a new gold-wire-bonded optional NTC thermistor for laser diode temperature measurement

    TDK Corporation (TSE: 6762) announced the introduction of the new NTCWS series of NTC thermistors with gold wire bonding. These bonding NTC thermistors can be installed in packages via gold wire bonding to enable high precision temperature detection of laser diodes (LD) for optical communication. The series will begin mass production in September 2023.The use of LD devices in optical communication...

    2023-09-08
    Ver traducción
  • Shandong Zhancheng Intelligent Manufacturing Laser Cutting Equipment is Popular Overseas

    The high-end laser cutting machine developed and produced by Dongying Lijin Zhancheng Laser Intelligent Manufacturing Company has become popular in overseas markets this spring. This equipment can not only use laser to quickly cut steel, but also freely swing on steel, "showing" beautiful pictures. The laser travels like a paintbrush flying, and the hard steel plate has been hollowed out into be...

    03-21
    Ver traducción
  • GE Additive has been renamed Colibrium Additive, continuing to lead the additive manufacturing industry

    In April 2024, GE Additive was renamed Colibrium Additive. Colibrium Additive (formerly GE Additive) is a subsidiary of GE Aerospace Propulsion and Additive Technology (PAT) and was established at the end of 2016. Nowadays, it is a trusted partner and manufacturer of industrial metal 3D printers and metal powders, as well as a service provider for industrial metal 3D printers and metal powders. It...

    2024-04-30
    Ver traducción