Ελληνικά

SEMA 2023: Huali's Easy Level Floating Free Laser Fuel Level Transmitter

849
2023-11-03 14:51:33
Δείτε τη μετάφραση

Winning the SEMA Best Engineering New Product Award is not an easy task. Therefore, it said a lot about Huali's new non floating fuel transmitter bringing hardware home. The Easy Level fuel level sender is a brand new design that does not rely on traditional float arm settings, but uses a frikken laser beam to measure the fuel level in the tank.

More precisely, Easy Level uses LiDAR technology to measure the distance between the fuel surface and the sensor unit, and then converts this distance measurement value into a signal that can be read by the fuel level gauge. It can be used with any aftermarket instrument, "said Steve Sparkman of Holley. It is not suitable for OEM instruments, but all aftermarket instruments - Classic Instruments, Dakota Digital, etc. - can be easily connected.

This sensor is suitable for tanks with depths ranging from 4 inches to 39 inches and can be set up outside the vehicle. By using the buttons on the device, you can set the empty and full positions before installation, and then set the same position on the instrument panel after installation. You can even adjust the damping rate of the reading through the DIP switch on the device to manage instrument bounce caused by fuel shaking.

This device is very compact and easy to install. It looks like a hockey ball, "Sparkman said. It has a laser that can shoot down and tell you where the fuel is. It's so simple. Installation is a simple task, including installing hardware and gaskets, as well as installing flange templates. The small bolt circle diameter of 2-1/8 inches hardly occupies space on the fuel tank, and the 12 volt PWM output signal makes sensor wiring easy.

Source: Laser Network

Σχετικές προτάσεις
  • Shanghai Institute of Optics and Fine Mechanics has achieved beam splitting vortex control and interference detection for the first time in the 46.9nm wavelength band

    Recently, Associate Researcher Zhang Junyong from the High Power Laser Physics Joint Laboratory of the Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, together with Professor Zhao Yongpeng's research group from Harbin Institute of Technology and Professor Zhan Qiwen's research group from Shanghai University of Technology, completed the experimental verification of 46....

    2024-10-17
    Δείτε τη μετάφραση
  • The rare decay of the Higgs boson may point to physics beyond the standard model

    Particle physicists have detected for the first time a new decay of the Higgs boson, revealing subtle differences predicted by the standard model and potentially pointing to new physics beyond it. The research results are published in the journal Physical Review Letters.The theoretically predicted Higgs boson since the 1960s was finally discovered in the European CERN laboratory in 2012. As a quan...

    2024-01-26
    Δείτε τη μετάφραση
  • Researchers have developed a QCL DFB continuous laser for gas detection

    Alpes Laser was founded in 1998 in Nazhatel, Switzerland and was the first company to bring quantum cascade lasers to the market. It released its first continuous laser in 2001 and its first high gain laser in 2009, thus maintaining this priority position.In 2004, the first commercial laser was introduced.Principle: In a single mode laser, the grating is etched into the active region to force the ...

    2023-08-16
    Δείτε τη μετάφραση
  • Trumpf 3D printing technology innovation: zero support structure, low waste, unlimited possibilities

    Ditzingen, Germany, September 8, 2023) - TRUMPF, the world's leading provider of machine tools and laser technology solutions, has improved its 3D printing software TruTops Print to print parts with suspension angles as low as 15 degrees with little need for support structures. Trumpf will present its new technology at the European International Machine Tool Show (EMO 2023) in Hannover, Germany.Fi...

    2023-09-13
    Δείτε τη μετάφραση
  • Swedish KTH develops 3D printed quartz glass micro optical devices on optical fibers

    In what has been described as the "first communication", Swedish researchers conducted 3D printed quartz glass micro optical devices on the tip of optical fibers. They said that this progress could lead to faster Internet and better connectivity, as well as innovations such as smaller sensors and imaging systems.Scientists from the KTH Royal Institute of Technology in Stockholm have stated that co...

    2024-05-23
    Δείτε τη μετάφραση