"Also, we’ve seen that for engraving at high speeds weare having a big overscaning each side of the job. We are working with servomotors, but even putting the acceleration to the maximum value (100000mm/s2), for 2000mm/s we have anoverscanning of 50mm eachside, and 60mm if wehave the reverse compensation settings adjusted. T...
2021-10-271.2K00"The cleaning of industrial parts is widely acknowledged as a key value-adding step in the overall production chain. But new trends – such as Industry 4.0, miniaturization, electromobility, vehicle lightweight design and new or modified manufacturing and coating technologies – pose new challenges for cleaning industrial parts and surfaces.The story...
2021-09-161.1K50"Indexers, dividing heads, spin jigs and many other rotary devices are common hardware in toolrooms and machine shops. Having the ability to accurately rotate a part through a circular path simplifies machining everything from keyways to bolt-hole circles.In the not-so-distant past, having a rotary device for a CNC machine in your job shop set you ...
2021-09-161K00"Shops have plenty of reasons to automate their CNC lathes. Throughput becomes more predictable. Labor costs go down with unattended machining. There’s a subsequent increase of available working hours. And don’t forget the primary motivation behind any foray into automation: It’s tough to find people with the required skills.Adding a robot can make...
2021-09-161.1K00"Deburring drilled holes is essential to the manufacturing process. Burrs that aren’t cleaned up can cause part failure by breaking off and clogging or damaging a part or an assembly or by cutting a wire or an O-ring that’s passed through a bore. But cross-holes, where two or more holes intersect, are hard to reach and often require deburring by ha...
2021-09-161.2K00"After being at AB Sandvik Coromant, Sandviken, Sweden, for 17 years, Nadine Crauwels was appointed global president of the cutting tool manufacturer in May 2017. She has had roles in sales, product management, product introduction, custom tools and strategic relations. In an interview with CTE Editor Alan Richter at IMTS 2018, Crauwels discussed t...
2021-09-271.4K00"Hi i have a Atomstacker 5.5w compressed spot fix focus laser and in the x direction it a very tight beam that cuts through 3mm ply in 3 passes. in the y direction its at least 2 to 3 times wider and at 8 times around and still not through. Im focusing how directed with a 2mm spacer below the shield."
2021-09-291.2K00"Hey there,I've been running and upgrading my little desktop router for the past few years, but I would still consider myself a newbie at motion control. I recently upgraded my setup from Mach3+LPT PCI card to using the KFLOP with the intention of running them in Closed Loop Mode. I never even got that far. I've read all the documentation and seen ...
2021-09-281.1K00"hi all was using my cnc today cutting well. then all of a sudden compressor burns out its motor which blows main fuse cnc crashes now when i re started it will not moveanyone had same problems if so how do you fix cheers"
2021-09-291.2K00"Hi,I am new to this and I have run into a problem with touch probing after I have grounded my table to the ground pin.My setup is that I have a power connection to the machine torch tip, and from a wire clamped to the cutting plate going to an input in the software.This results in input activating when machine torch tip touches the cutting plate. ...
2021-09-291.1K00How to realize laser control with open laser galvanometer motion controller？
2022-09-281.1K00Key technologies of laser cutting system for pipes1. Light guide focusing systemThe function of the light guiding and focusing system is to guide the light beam output by the laser generator to the cutting head of the focusing light path. For laser cutting pipe, to get high-quality slit, it is necessary to focus the beam with small spot dia...
2022-05-271.1K00When user use RDC6442G or RDC6442S to do a cutting and engraving, different auxiliary gas pressure should be set according to engraving and cutting . usually engraving should set a low pressure auxiliary gas and cutting should set a strong gas .For RDC6442 series， there is only a port named <wind> to control auxiliary gas. here is a ex...
2022-01-241.2K02Description of the auto-focus functionThere are 2 options for the auto-focus function in RD controllers. See the picture below.  ...
2021-11-291.1K00RD Controllers has USB and Ethernet port for data sending. For some cases, if the USB port is burnt out, User can try the Ethernet port to make the controller working. user can follow the steps to set up a Ethernet connection with RD controllers.1 Prepare a Ethernet cable and make sure the cable can do a correct internet connection.2 Connect the ca...
2021-10-291.3K00
- Δεν υπάρχουν δεδομένα
Ελληνικά
- English
- 简体中文
- 繁体中文
- Français
- Русский
- Italiano
- 日本語
- 한국어
- Português
- Deutsch
- Español
- Türkçe
- Ελληνικά
- Nederlands
- Tiếng Việt
- Polski