Deutsch

Widely tunable terahertz laser enhances photo induced superconductivity in K3C60

516
2023-10-13 14:41:30
Übersetzung anzeigen

Researchers at the Max Planck Institute for Material Structure and Dynamics (MPSD) in Hamburg, Germany, have long been exploring the effect of using custom laser drivers to manipulate the properties of quantum materials to deviate from equilibrium states.

One of the most eye-catching demonstrations of these physics is unconventional superconductors, where enhanced electron coherence and super transport characteristics have been recorded in the resulting non equilibrium states. However, mainly due to the complexity of the experiment, these phenomena have not been systematically studied or optimized. Therefore, the application of technology is still far from reality.

In a recent experiment, the same group of researchers discovered a more effective method of using lasers to create previously observed metastable, superconducting like states in K 3C 60. The research results of the Cavalieri group are published in the journal Nature Physics.

Researchers have shown that when the laser is tuned to a specific low-frequency resonance, much lower intensity light pulses can produce the same effect at higher temperatures. The laser technology developed by the research institute is the key to this work. By adjusting the light source to 10 THz (a frequency lower than previously possible), the team successfully reproduced a long-lived superconducting state in fullerene based materials, while reducing the pulse intensity by 100 times. This light induced state can be directly observed to last for 100 picoseconds at room temperature, but its lifespan is expected to be at least 0.5 nanoseconds (nanoseconds are billionths of a second, picoseconds are trillions of a second).

Edward Rowe, a doctoral student and lead author of the Cavalieri group, said that their findings provide new clues to the potential microscopic mechanism of photo induced superconductivity: "Identification of resonance frequencies will enable theorists to understand which excitations are actually important, as there is currently no widely accepted theoretical explanation for this effect in K3C60

Rowe envisions that a light source with a higher repetition rate at a frequency of 10 THz can help maintain metastable states for a longer time: "If we can transmit each new pulse before the sample returns to its non superconducting equilibrium state, then it is possible to maintain a quasi superconducting state continuously.

Andrea Cavalleri, Director of MPSD, said: "These experiments demonstrate well how appropriate technological advancements can make many so far unrealistic phenomena feasible." He believes that two years of effort in exploring these effects will converge into future technologies. It is equally evident that a key bottleneck that needs to be addressed is the type and availability of laser sources, which should go hand in hand with these studies to promote the development of this field.

The study was conducted at the MPSD Free Electron Laser Science Center (CFEL) in Hamburg. It is supported by DFG (German Research Foundation) through the Excellence Cluster CUI: Advanced Material Imaging. The K 3 C 60 sample was prepared at the University of Parma in Italy.

Source: Laser Network

Ähnliche Empfehlungen
  • New discoveries bring progress in photon calculation

    International researchers led by Philip Walther from the University of Vienna have made significant breakthroughs in the field of quantum technology, successfully demonstrating quantum interference between multiple single photons using a new resource-saving platform. This work, published in Science Advances, represents a significant advancement in the field of quantum computing and paves the way f...

    2024-04-27
    Übersetzung anzeigen
  • Which automotive parts can use laser soldering technology

    Laser soldering is widely used in the manufacturing of automotive parts. Here are some common automotive parts that can be welded using laser soldering:Automotive electronic control systemEngine Control Unit (ECU): The engine control unit is the "brain" of the car engine, which receives signals from various sensors and controls the operation of the engine based on these signals. Laser soldering ca...

    02-10
    Übersetzung anzeigen
  • Microstructure evolution and mechanical properties of Ti-6Al-4V alloy prepared by dual ultrasonic vibration assisted directional energy deposition

    1. Research backgroundDirected energy deposition (DED), as an efficient and economical technology in the field of additive manufacturing (AM), is widely used in the manufacturing of metal materials. However, its high heating and cooling rates, as well as significant temperature gradients, often lead to rapid solidification, forming cross layer columnar grains and internal defects, seriously affect...

    03-21
    Übersetzung anzeigen
  • The 3D toy printer is easy to use and safe, perfect for children and adults

    Children (and adults) like to collect toys, but what if they can make them themselves? This is exactly the focus of the Toybox 3D printer luxury bundle. This 3D printer for children's toys incorporates innovative technology into simplified products, making it very suitable for young people. Do you want to have your own? The cost of this 3D toy printer has been reduced to $348.99.Generally speaking...

    2024-06-05
    Übersetzung anzeigen
  • Artists transform paper into meticulous laser cutting designs

    In the past few years, paper artists have demonstrated the versatility of their common fiber materials. Some people manually cut or carve paper, while others combine traditional craftsmanship with digital design. Ibbini Studio is in this situation. Abu Dhabi artist Julia Ibni collaborated with computer scientist Stephen Noye to create sculptural paper works inspired by decorative patterns such as ...

    2024-01-23
    Übersetzung anzeigen